GOST to develop working documentation 21.1101. General requirements for the composition and acquisition of project and working documentation
GOST R 21.1101-2013 Basic requirements for project and working documentation
The objectives and principles of standardization in the Russian Federation are established by the Federal Law of December 27, 2002 No. 184-FZ "On Technical Regulation", and the rules for the application of national standards of the Russian Federation - GOST R 1.0-2004 "Standardization in the Russian Federation. Outdoor positions »
Information about the standard GOST R 21.1101-2013
- Developed by an open joint-stock company "Center for the Methodology of Regulation and Standardization in Construction" (OJSC TsNS)
- Made by Technical Committee TK 465 "Construction"
- Approved and put into effect by the Order of the Federal Agency for Technical Regulation and Metrology of June 11, 2013 No. 156-Art C1.01.2014
- In this standard, the norms of the Town Planning Code of the Russian Federation of December 29, 2004, No. 190-FZ
- Instead of GOST R 21 .1101-2009
3. Terms, definitions and reductions
3.1 Terms and Definitions
In GOST R 21.1101-2013 "The basic requirements for project and working documentation" are applied, GOST R 21.1001, GOST R 21.1002, GOST R 21.1 003, as well as the following terms with the corresponding definitions:
3.1.1 Basic inscription - A combination of information about the project document contained in the columns of the table of the established form placed on sheets of project and working documentation.
3.1.2 Main set of work drawings - a graphic document containing the necessary and sufficient information in the form of drawings and schemes intended for the production of construction and installation works of a certain type (mark).
3.1.3 A complete set of working documentation - a set of major sets of work drawings required for the construction of a building or structure, complemented by the attached and reference documents.
3.1.4 Marka - An alpoint or alphanumeric index, which is included in the designation of working documentation and determining its attitude to a certain type of construction and installation work, or denoting the main distinguishing features of building structures and their elements.
3.1.5 Specification of equipment, products and materials - Text project document that determines the composition of the equipment, products and materials intended for the acquisition, preparation and implementation of construction.
3.1.6 Sketch Drawing of General View of the Nepical Product - A document determining the original construction of the non-type product containing a simplified image, the main parameters and technical requirements for the product in the amount of source data (tasks) required to develop design documentation.
3.1.7 Nepical Product - the product (design, device, mounting unit) of technological systems, internal and external systems and networks of engineering and technical support of buildings and structures, first developed and manufactured, as a rule, at the installation site (in the procurement workshop of the assembly organization).
3.1.8 Construction construction - part of a building or structure that performs certain carriers, about citizens and (or) aesthetic functions.
3.1.9 Construction Product - Zdeli, intended for use as an element of buildings, structures and building structures.
3.1.10 Element of the Construction Design - Composite part of the national team or monolithic design.
3.1.11 Building Material - Material, including Stuchane, intended for the manufacture of building products and the construction of building structures of buildings and structures.
3.1.12 Equipment - Technological equipment (machines, apparatus, mechanisms, lifting and other technical means providing the appropriate technological process), as well as engineering equipment of buildings and structures, ensuring safe and favorable conditions for people's vital activity.
3.1.13 Coordination Ace - One of the coordination lines that determine the membership of the building or structure to the modular steps and the height of the floors.
3.1.14 Plan - Top view or horizontal section of a building or structure.
3.1.15 Facade - orthogonal projection of the outer wall of the building or facilities on the vertical plane.
Note. Distinguish the facades of the main, side, yard, etc. 3.1.16
3.1.16 Document props - An element of the design of a document containing information about it.
Note. As a rule, props consists of attributes (composite props).
3.1.15 Attribute of the document - identified (named) characteristic of part of the props.
3.1.18 Document design - Locusing the necessary details and attributes established by the documentation rules.
3.1.19 Signature - Props of the document, which is a personal signature of the authorized official.
Note. For electronic documents, an analogue of its own signature is an electronic digital signature.
3.1.20 Designation - props of the document, which is its identification (distinctive) index.
Note. Each document is assigned the designation that is recorded in the established places (in the main inscriptions, on title sheets, etc.).
Explanations to the most important changes in GOST R 21.1101-2013
(compared to GOST R 21.1101-2009)
Section 3 "Terms and Definitions"
The terms "main set of workers drawings", "Plan", "Facade", "Equipment", "Building Material" are introduced.
Because Some terms entered the Interstate Standard GOST 21.501-2011, then in this National Standard (GOST R), they are given both borrowed (within, with reference to GOST 21.501).
The section is supplemented by terms from GOST 2.102 (props, attribute, etc.), which are necessary to understand the rules for filling the main inscriptions, covers and title sheets.
Subsection 4.1 "Project Documentation"
Paragraph 4.1.1
Section 5 - usually the largest section. For large projects, as it turned out, often lacks the division of this section on "parts (they are subsections) - books." Therefore, it provides for section 5 that the subsections of this section are divided into parts and books.
In accordance with this basic change, appropriate changes are made to clauses 4.1.2 and 4.1.3.
It is determined that the words about the "large volume" of the documentation relate to the documentation on paper. Based on this volume, the section (or subsection) is divided into parts and books.
In addition, a new position has appeared that the section and subsection can be divided into parts and books not only depending on the amount of documentation, but also by other features (for example, when performing some part of the project documentation by subcontractors).
Paragraph 4.1.3.
This item is recycled due to the fact that the sections and subsections are divided into parts and books. For section 5, another degree of division appeared.
"The designation of the subsection complied with the form of a separate volume (see 4.1.1), is from the designation of the section to which the subsection number is added.
If the subsection is divided into parts, the designation of the part is made up of the designation of the subsection to which the part number is added via the point. If the part is divided into books, the designation of the book (if necessary) is made up of the part of the part to which the book number is added through the point. "
In this regard, examples were changed.
At this point, the following paragraph appeared:
"Based on provisions 4.1.1 - 4.1.3, 4.2.3 - 4.2.7, standards of organizations on the designation of textual and graphic documents that are part of the design and working documentation that take into account the characteristics of the designation depending on the volume of documentation, document management conditions and used CAD and SED. "
Paragraph 4.1.4.
In this point, the words "are generally completed in the following order".
This means that it may not be necessary for all of the documents listed below.
For very large projects, many dozens, or even hundreds of volumes, it is planned to be the possibility that the document "The composition of the project documentation" is not included in each volume - it is completed in the form of a separate volume.
Naturally, this assumption should be applied when the number of volumes is significantly larger (several times) than the number of project documentation sections (now 14 of them).
Subsection 4.2 "Working Documentation"
Paragraph 4.2.1. The first listing is reduced, because Everything is already written in the definition of the term "main set".
Paragraph 4.2.5.
According to the new edition of the Standard, it is allowed to form the main sets of work drawings with individual documents for any brand, and not just electrical stamps.
Paragraphs 4.2.6 and 4.2.7
This clause is listed only the most general accompanying documents that can be included in any brand.
Under the "other" are understood, for example, the "statement of pipelines" in GOST 21.401-88, "Specification of the metal" according to GOST 21.502-2007.
With greater details, the general principles of the designation of the attached documents are given.
In the example for the specification of equipment, products and materials, the cipher "C" - according to the current GOST 21.110-95. In the project of the new GOST 21.110, this cipher is changed to "CO".
Paragraph 4.2.8.
Due to the uncertainty of the status of "typical building structures (" series ") (they are not canceled, but at present there is no current regulatory document establishing the procedure for the development and application of these drawings) to this item a footnote:
"If necessary, drawings of typical designs, products and nodes are recorded without changing the designation in the" Accellenged Documents "section and transmitted to the Customer in accordance with 4.2.6."
Paragraph 4.2.9.
"4.2.9 The form, rules for the implementation and designation of the document, which provides the composition of all working documentation, made in accordance with the Treaty, are established in the standards of the organization."
Paragraph 4.3.5
Some requirements for general instructions are refined, in particular to the list of regulatory documents.
Added paragraph about the need to number the points of general instructions.
Subsection 5.1 "General"
This subsection is substantially supplemented, mainly by reference to ECC standards on electronic documents and the rules of their appeal, which with certain assumptions can be used for project documentation.
A clause is introduced on the possibility of using types of lines missing in GOST 2.303:
"5.1.3 in the graphic documents of the image and the symbols are performed by lines according to GOST 2.303. It is allowed to use other types of lines, names, drawing, thickness and main purpose of which are installed in the relevant SPDS standards. " (This contains in mind GOST 21.501-93 (clause 2.5.1), GOST 21.204-93, GOST 21.302. These types of lines that are missing in GOST 2.303 are installed).
The subsection is supplemented with the requirements for the performance of the drawings in the color form:
"5.1.4 In graphic documents, the conditional designations should be carried out in the main black color. Some conditional designations or their individual elements are allowed to be performed by other colors. Instructions on the color of the symbols are given in the relevant SPDS standards. If the color of the symbols used in the drawings and diagrams are not installed in the standards, their purpose indicates the drawings.
In the originals intended for the manufacture of black and white copies, color conditional designations and their elements should be performed in black. "
It should be noted that in GOST 21.302, the requirements for the colors of symbols have long been established. Therefore, this item is just a statement of fact.
Paragraph 5.1.6
Required rules for applying images of images in the drawings.
The second paragraph of this point is complemented by the following proposal:
"In these cases, the scale is indicated in parentheses immediately after image names in accordance with GOST 2.316 (paragraph 4.19)."
Clause 5.1.10
"5.1.10 for consideration, approval, examination and approval are copies of documents of project and working documentation, compounded as indicated in 4.1 and 4.2."
This item establishes (or rather, reminds) what exactly is transmitted to customers. The definition of the term "copy" is given in GOST R 21.1003.
Subsection 5.2 "Main inscriptions"
Paragraph 5.2.1
This point is given a refined answer to a very long and frequently asked question: "Is it possible to have the main inscription on the long side of the A4 format?"
Now the answer is "you can", but in certain cases:
"For text documents in tabular form is allowed, if necessary, to have the main inscription along the long side of the sheet."
In the appendix and this corresponding Figure and.2.
Paragraph 5.2.2.
The concept of "Capital Sheet" was introduced for documents with title sheets - this is the next after the title page of the text document, which is made in the main inscription in the form 5. This sheet cannot be called first, because The first sheet of the document decorated with a title list, according to P.8.5 is the title page. Indeed, in this case, in the column "Sheet" of the main inscription in form 5 is the number 2!
This term is not something new, it is applied in ECCD standards (GOST 2.104 and GOST 2.106) and was in CH 460-74 (part 1).
Accordingly, the name of the form 5 is fixed in the Appendix J.
Paragraph 5.2.3.
The word "Text" added to the first paragraph: "If some text documents ...".
This item has moved and supplemented with a note to form 6 of the application.
"When designing a basic set of work drawings with individual documents, documents containing solid text and / or in the form of tables (for example, general data, cable log, etc.), are issued as text documents. In this case, the first sheet of the document is drawn up by the main inscription in form 3, subsequent - in form 6. "
New paragraph 5.2.9
"5.2.9 is allowed to additionally identify project documents using barcode.
At the same time, the country code, the code of the developer organization, the designation of the document and the designation of the document should be used as props of the barcode. Other details can be used in addition.
The barcode is recommended to be placed in the lower right corner of the field of the format of the document on the main inscription. "
The barcode makes it possible to quickly search for documents using a manual scanner installed at the user's workplace. Barcode is also used to identify when scanning.
The barcode is calculated automatically when filling in the details of the main inscription and recorded in a special field.
The recommended location of the barcode is taken from the ECC standard.
This provision is given in subsection 5.2, because The barcode contains the same data as the main inscription.
Subsection 5.2 "Coordination axes
Paragraph 5.3.1
In this new paragraph, the main purpose of the coordination axes is formulated:
- to determine the mutual arrangement of elements of the building or facilities;
- To bind a building or facilities to a construction geodetic grid or a center base.
Paragraph 5.3.2.
The possibility of designation by the coordination axes of the Latin alphabet letters is introduced.
Paragraph 5.3.3
The item is shown in the refined form: "The sequence of the coordination axes is taken according to plan as shown in Figure 1a: Digital axes - from left to right, alphabetic axes - from the bottom up, or as shown in Figures 1B and 1B.
Clause 5.3.7 Dan in the new edition. Instead of an example, with the designation of the coordination axes of the sections, a more understandable Figure 3b is given, which was in the 1980 standard.
Paragraph 5.3.8.
This clause presents the most common provisions related to the coordination axes in 3D models.
Subsection 5.2 "Applying sizes, slopes, marks and inscriptions"
Paragraph 5.4.3.
Changed the size of the protrusion line. The minimum value is proposed to be changed by 0, i.e. "... In this case, the dimensional lines continue for extreme remote lines (or accordingly for contour or axis) by 0 3 mm."
Those. Selo may be like an example from MS ISO 4066: 1994 (see Right).
For example, in GOST 28984-2011 - only such serifs. See also SP 63.13330.2012.
The last paragraph of this item has been restored, which establishes the rules for drawing the sizes with arrows in the construction drawings.
Also given the following additional paragraph:
"When drawing dimensions on axonometric schemes of technological pipelines and engineering systems, dimensional lines are allowed to limit the arrows."
If you carefully read the first paragraph of paragraph 5.4.2, then its requirement cannot be performed, for example, for a rowed isometric projection (at an angle of 45 °).
Paragraph 5.4.3.
The word "relative" is added to the last sentence, i.e. It turned out "The relative marks above zero indicate with the" + "sign, below zero - with the sign" - "."
In accordance with the current standards, absolute marks indicate without a sign of "+" - in the drawings of the General Plan, automotive and railways, hydro-elevative and other structures.
A note explaining the concept of "zero mark" for buildings:
"As a zero mark for buildings, usually take the level of the first floor floor."
Paragraph 5.4.4.
An additional figure 7b is given, explaining the rule of application of slopes.
Paragraph 5.4.6.
A new Figure 8 is given, which sets the order of bringing outwards for all cases, in particular, when the arrow is below. In GOST 21.701 and GOST 21.702 (instead of GOST R 21.1701-97 and GOST R 21.1702-96), examples that do not meet this requirement are fixed.
Subsection 5.5 "Images (cuts, sections, species, remote elements)"
Paragraph 5.5.2.
This paragraph provides a note that explains the features of the application of the term "incision" in the construction drawings - unlike the design documentation.
All terms on the images are given in GOST 2.305-2008, and in this standard only the terms defining individual types of images used only in construction documentation (plan, facade), and which are not available in GOST 2.305.
Paragraph 5.5.15
The new last paragraph is given:
"It is allowed in the name of the facade to indicate its location, for example," chief "," yard ", etc."
Section 6 rules for performing specifications in the drawings
Paragraph 6.1.
The words "as well as to other drawings" are added, since the specification for forms 7 and 8 is used for product drawings (in accordance with GOST 21.501-2011) and for sketching drawings of non-type products.
Point 6.3.
This paragraph contains the most general requirements (from GOST 2.316) to perform specifications and tables in 3D models of a building or structure.
What should be noted here.
From this point, as well as paragraph 4.1 of GOST 2.316-2008, it follows that the specifications, etc. Tables in electronic models are allowed (in GOST 2.316 it is even recommended) to perform individual documents, and in paragraph 4.2.5 of this standard, it is possible how it can be performed For working documentation.
Section 7 "Rules Amendments"
This section is significantly recycled. First, the general provisions are given (7.1 - 7.3, and then subsections are given with the features of making changes to project and working documentation.
Clause 7.1.1
This clause is recorded that on the basis of the provisions of section 7, standards of organizations that take into account the features of making changes in these organizations can be developed.
Subsection 7.2 "Resolution on making changes"
Paragraph 7.2.4.
Added new paragraph:
"Changes in documents of the main kit of working drawings decorated with separate documents (see 4.2.5), as well as in the documents of the project documentation volume, are made on the basis of one general permission."
New paragraph 7.2.5.
"7.2.5 When making changes to DE, permission is allowed not to do, if the CAD and EDD accounts and storing the versions of the document, and access controls, excluding the possibility of unauthorized changes."
Necessary explanation to this item. The permit is allowed not to be issued if the projects are signed by electronic signatures in the project organization - only this eliminates the possibility of unauthorized amending the CAD and EDS.
Subsection 7.3 "Amendments"
This subsection shows common for the design and working documentation of the requirement. (In brackets gives the numbering of the relevant items in GOST R 21.1101-2009)
Clause 7.3.5
Attention should be paid to this item:
"7.3.5 by a handwritten way of change is made in paper origards of documents in accordance with 7.3.9 - 7.3.16."
Clause 7.3.11 (7.1.3.8)
Here we removed the words about "annulible" sites, because In relation to the images in the drawing, this word has not previously been used before and is not used.
It is not necessary to note this and do not need - even when driving: if not specified, where to look a new image (as indicated in clause 7.3.14), then this means that the site is removed without replacement.
If the site is simply removed (which was allowed even when manually making changes - washes), then this number simply nowhere to bring.
Clause 7.3.12 (7.1.3.9)
Added two new paragraphs:
"It is allowed from the parallelogram with the designation of the change of the line to the changed area not to be carried out.
When making changes to text documents (in the text part of the documents), the line from the parallelogram is not carried out with the designation. "
Clause 7.3.19 (7.1.3.20)
Here you need to explain words about the additional table for making changes (see 5.2.6). This continuation of the table is only needed by making changes by a handwritten way.
Added paragraph:
"In the new (modified) version of the DE in the Change Table indicate the data only on the last change."
Clause 7.3.21 (7.1.3.21)
Changed the rules for filling the Graph "Sheet" in the Change Table
3) When replacing all sheets of the original when manually making changes in the first (title) sheet - "All" (the table of changes on other sheets does not fill in this script), an automated way - "Deputy" On all sheets.
According to many, the number of the current version of the sheet (document) must be on all sheets of the document. That is, by the way, it is also given in GOST 2.503-90.
Those. When replacing all the sheets of the document automated method, the table is filled in all sheets: Count "Changes", "Doc." And the "date" (these graphs on text documents are usually filled automatically on all sheets).
Count "Kol.ch." not filled, because Plots do not allocate with a complete replacement of the document.
About the column "Sub." see below.
(If the text documents are performed without basic inscriptions, then the version of this document is given in footer on all sheets).
Listing e) is shown in the new edition:
"D) in the column" Sub. " - signature of the person responsible for the correctness of the change. When replacing all the sheets of the original automated method, the signature is affixed only on the first (title) sheet. The signature of the normocontroller is affixed in additional graphs on the leaf cover (except for sheets released instead of replaced and new); "
When replacing all sheets of the original when manually making changes, the change table (consequently, the Count "Sub.") Fill only on the first (title) sheet.
If you do not lead this underlined position, it turns out that with the automated changes in the column "sub." Change tables need to be written even where it is not provided to sign when manually making changes, for example, in the main inscriptions in form 6 on all subsequent sheets of a text document, and the number of sheets can reach several hundred!
Just absurd to force someone to sign in this graph on all sheets of replaced document, because When replacing sheets, all performers are symboling in graphs 12 of the main inscription (according to claim 7.3.23).
Paragraph 7.3.23 (new)
"7.3.23 When replacing sheets of documents issued by the main inscriptions in forms 3 - 5, the sheets released instead of replaced are signed in graphs 10 - 13 of the main inscriptions in accordance with the procedure provided for for newly developed sheets."
Subsection 7.4 "Features of making changes to project documentation"
Paragraph 7.4.5.
In this paragraph, as well as in Appendix M, N and P, the rules for applying a table of registration of changes in form 10 on the covers and title sheets are refined.
Added new paragraph:
"The state registration table does not take into account the corrections made to the statement of the composition of project documentation in connection with the changes in other volumes of project documentation."
Paragraph 7.4.7
This is a new position:
"7.4.7 When performing additional volumes of project documentation, corrections contribute to the statement" The composition of project documentation ".
Information about the changes in the "composition of project documentation" in the content of volume do not lead. "
Paragraph 7.4.8.
Added underlined words:
"7.4.8 Changes to the approved project documentation related to a change in the parameters of the construction facility that affect its design reliability and security, and the need to apply project documentation, contribute to the customer's decision on the basis of a new job design or addition to the previously approved design task.
Subsection 7.4 "Features of making changes to working documentation"
Paragraph 7.5.3 (7.1.3.16)
The item is complemented by paragraph:
"When making changes to the handwritten way of the number and the name of the canceled sheets in the statement of the working drawings, they are burned by an automated method - the" name "account for the annulled sheets is not filled."
Paragraph 7.5.4 (new)
"7.5.4 When making changes to the documents of the main kit, issued by individual documents, make appropriate corrections to the statement of documents of the main set of work drawings."
Paragraph 7.5.5 (7.1.3.18)
Fixed bug. The item is given in the formulation of GOST 21.101-97:
"7.5.5 When performing additional and cancellation of previously accompanying documents, corrections contribute to the section" The Acceived Documents "of the Lord of the reference and accompanying documents of the corresponding major set of work drawings."
This statement is not intended to track changes in the documents recorded in it!
Otherwise, it turns out that a new version of the main kit is created, when we did not make any changes at all, and the changes were only in the documents not included in the main kit!
The versions of the attached documents are not related to the versions of the main kit.
The same in clause 7.5.6 (7.1.3.19). The conduction of the main kits does not reflect information on the versions of the main kits recorded in this statement - information is given only on the implementation of additional and cancellation of previously performed main sets of work drawings!
Clause 7.5.7 (7.1.3.22)
The item is complemented by the underlined words:
"7.5.7 In the tables of changes on sheets of general data, corrections made in the general data statements in connection with the introduction of changes in the sheets of the main kit and the accompanying documents are not taken into account as sections of changes in accordance with 7.3.11."
Section 8 "Rules for registration of a discrepanied documentation"
Paragraph 8.5.
The provisions of this paragraph became "recommended". At the same time, the standard is now given (in paragraph 8.6), how to fill the content in the absence of additional pass-through numbering of sheets.
Paragraph 8.6.
This point is recorded:
"The graphical documents of the project and reporting technical documentation on the results of engineering surveys are recorded poliste."
The rules for filling the content are given:
"In content graphs indicate:
- in the column "Designation" - the designation of the document;
- in the column "Name" - the name of the document in full compliance with the name specified in the main inscription or on the title page;
- In the Count "Note" - information about the changes made to the recorded documents, as well as the number of the volume sheet on the pass-through numbering of TOM sheets in accordance with 8.5, from which the document begins.
If the pass-through numbering is not performed, then in the "Note" column, the total number of sheets of each document leads. At the end of the content, give the total number of sheets included in the (album, folder).
It also should also be noted that in the appendix in now it is written that in form 2 "is allowed to include additional graphs (columns) in the statement, for example," count. sheets ", etc."
Paragraph 8.7. With the introduction of the last paragraph of this item, questions and disputes on the need for seals on title sheets should be discontinued. For some reason, it was necessary for the survey documentation and do not need (if more precisely, it was not established) for the design and working.
Section 9 GOST R 21.1101-2009 is not included in the draft new standard. It is proposed to develop a separate national standard or a set of rules. This section was not the requirements for project documentation - it had provisions (rules) to reuse the already developed documentation.
It was impossible to leave it in the existing form, because He does not match anything.
In addition, there is a draft law on the reuse of foreign project documentation, which should also be taken into account in a new document on re-use documentation.
Appendix A.
Added note about the possibility of designation of sections of sections with letters of the Latin alphabet.
Section numbers 101 and 111 are given on the draft change of government decree No. 87.
Recommendations on allowed by writing these strange partition numbers are given:
"Partition numbers 101 and 111 are allowed to bring in form 10 (1), 11 (1) or 10-1, 11-1.
Those. You can any option, but the option with a dot should not be, because According to clause 4.1.3, it turns out that this will be the designation of part 1 of section 10 or 11, and not the number of the independent partition.
Appendix B.
The brands of the working documentation are given (tried to lead) in the sequence corresponding to the sections and subsections of project documentation.
Added note about the possibility of designation of stamps of basic sets of Latin alphabet letters.
The designation of the brands of the main sets of Latin is possible for two options:
1) When letters coincide in Russian and Latin alphabets (for example, AR, VC, NVK, TS, etc.) are used in the brands (for example, AR, VK, NVK, TS, etc.), the transliteration of the Russian notation is not performed. New brands Latin letters are assigned only in cases where the Russian letters are not in the brand, missing in the Latin alphabet (b, g, d, z, s, p, u, etc.);
2) When all the brands denote Latin letters without taking into account the coincidence of letters, and, for example, based on the English translation of the brand name.
All this is allowed to establish at the discretion of the project organization in the standards of organizations.
Appendix G.
In instructions on the filling of the general data statements, the provisions allowing the change in the size of the graph of the forms of these statements, as well as the possibility of bringing additional graph (columns).
In explanation to fill the statement of documents of the main kit (clay 5), the following is given:
"For graphic documents consisting of several sheets, the names of images placed on each sheet are also given in accordance with the names given in the main inscription of the sheet."
This means that on the first sheet of the document of the main kit does not need to lead a statement of the working drawings of the document, as provided for in GOST 21.607-82. Not all documents of the main kit are graphic. For text documents, it suffices to bring the number of sheets of this document in the "Note" column.
Appendix E.
Two new cuts were introduced:
Revoked - Annun.
The level of soil (underground) waters - CE.
There was a proposal to reduce "canceled" to "Ann", but this does not correspond to paragraph 6.5 GOST R 7.0.12-2011 "System of standards according to information, library and publishing. Bibliographic record. Reducing words and phrases in Russian. General requirements and rules. "
Adopted a reduction, similar to the reduction of the word "abstract" - "Annot."
Changed abbreviations:
Coefficient "- coefficient; (6.5. If the complicated part of the word is preceded by a double consonant, with a reduction, one of the consonants should be saved).
Efficiency ratio - efficiency.
Pure floor level - uch.
The following note is given:
"Reducing the words shown in this table and GOST 2.316 is allowed to be used in text documents containing text, broken into graphs."
Appendix J.
It should be paid to the fact that the number of lines in the graphs "coordinated" on the left leaf field is reduced to three, because Comments came that the word "coordinated" is not printed on some types of printers. It should be noted that it was also done in a similar Ukrainian standard of 2009.
In directions to fill in Graph 2 added underlined words:
"- in column 2 - the name of the enterprise and, if necessary, its part (complex) ,.". Next - by text.
Instructions for filling Count 4 are supplemented with three positions that are practically carried out by all, but have not been described in Standard:
"If one image is placed on the sheet, it is allowed to bring it only in column 4.
On the sheet (sheets) of general data on working drawings in the column record "General data".
In the case provided for in 5.2.3, in column 4 lead the name of the document or the inepar product. "
Instructions for filling Count 10 are significantly revised. In the last paragraph changed the order of the "most significant sheets", because From the previous edition, for some reason, it was concluded that the gips sign all the sheets of the graphic part of the project and documentation:
"The bottom line provides the position of person who approved the document, for example, the chief engineer (architect) of the project, the head of the department or another responsible for this document (sheet) of an official.
Signatures of the person responsible for the preparation of project or working documentation (the chief engineer (architect) of the project) are mandatory on sheets of general data on working drawings, the most significant sheets of the graphic part of the project documentation and work drawings. "
In the note to explanations to fill the main inscriptions added "for example, 02/02/12. This should clarify what the "calendar date" is and the format of filling the Count "Date".
It is possible to perform ("if necessary") in the main inscription of the additional graph 27 (above Count 1) to bring the name of the organization - the customer. Now in many cases, Count 2 is used for this.
This graph is in no way mandatory - it is introduced "if necessary", which the project organization itself establishes.
A similar graph is provided in the design of GOST 2.1044-2006 - and also "if necessary."
Appendix I.
Added Figure and.2, which shows the allowable option for the main inscription for A.4 format (see 5.2.1). Please note that the field for the binder still remains along the long side of the sheet.
Appendix K.
Instructions for filling the Count "Name" are significantly supplemented.
Appendix L.
Several modified forms 9 and 9a - the dimensions and location of the graph 2 and 3. They became more convenient for filling.
Appendix N and P
The new edition of the standard shows separate forms for the cover and the title leaf.
The mold of the title leaf and cover are complemented by fields for writing data on the certificate of SRO and, if necessary, the names of the customer's organization.
(Under the "customer" here it is understood not necessarily the "technical customer" (according to the GRK), but also the general proofer) - for the subcontractor.
In the instructions for filling the title sheet and the cover, the listing related to the filling of the "Tom number" field is fixed. Now it is given as follows:
"- Tom number on the statement" The composition of the project documentation "or" The composition of the reporting documentation on the results of engineering surveys "(if any).
Guidelines for filling the cover and the title leaf are supplemented by the following explanation:
"The field sizes are set arbitrarily; The lines of the fields specified in the form are not applied; The numbers and names of the fields do not indicate. "
GOST R 21.1101-2013
Group Z01
National Standard of the Russian Federation
System of design documents for construction
Basic requirements for project and working documentation
System of Design Documents for Construction. Main Requirements for Design and Working Documents
OX 01.100.30
Date of introduction 2014-01-01
Preface
1 Developed by an open joint-stock company "Center for the Metrationing and Standardization Methodology" (OJSC "CNS")
2 Submitted by the Technical Committee on Standardization TC 465 "Construction"
3 approved and enacted by order of the Federal Agency for Technical Regulation and Metrology of June 11, 2013 N 156-st
4 In this standard, the norms of the Town Planning Code of the Russian Federation of December 29, 2004 N 190-FZ
5 instead of GOST R 21.1101-2009
The rules for applying this standard are established inGOST R 1.0-2012 (Section 8). Information on the changes to this standard is published in the annual (as of January 1 of the current year) the information indicator "National Standards", and the official text of the amendments and amendments - in the monthly information indicator "National Standards". In case of revision (replacement) or the cancellation of this standard, the appropriate notification will be published in the nearest issue of the monthly information indicator "National Standards". Relevant information, notice and texts are also posted in the public information system - on the official website of the Federal Agency for Technical Regulation and Metrology on the Internet (GOST.RU)
The amendment is made by the database manufacturer
1 area of \u200b\u200buse
This standard establishes the basic requirements for project and working documentation for the construction of various appointments.
Note - In this standard, the concept of "construction" includes new construction, reconstruction, technical re-equipment and overhaul of capital construction facilities.
The general rules for the implementation and recruitment of graphic and text documentation established in 4.1 and in sections 5 and 8, and the rules for making changes established in Section 7 are also applied to the reporting technical documentation on the results of engineering surveys for construction.
2 Regulatory references
This standard uses regulatory references to the following standards:
GOST R 6.30-2003 Unified documentation systems. Unified system of organizational and administrative documentation. Document Requirements
GOST R 21.1001-2009 Project documentation system for construction. General provisions
GOST R 21.1002-2008 Project documentation system for construction. Normocontrol project and working documentation
GOST R 21.1003-2009 Project documentation system for construction. Accounting and storage of project documentation
GOST R 21.1703-2000 System of project documentation for construction. Rules for performing working documentation of wired communication
GOST 2.051-2006
GOST 2.052-2006
GOST 2.106-96 Unified system of design documentation. Text documents
GOST 2.109-73
GOST 2.305-2008
GOST 2.308-2011 Unified system of design documentation. Instructions forms and location of surfaces
GOST 2.309-73 Unified system of design documentation. Roughness designation surfaces
GOST 2.312-72
GOST 2.314-68 Unified system of design documentation. Instructions in the drawings on the labeling and branding of products
GOST 2.317-2011 Unified system of design documentation. Axonometric projections
GOST 2.501-88 Unified system of design documentation. Rules for accounting and storage
GOST 21.110-95 The system of project documentation for construction. Rules for the implementation of the Specification of Equipment, Products and Materials
GOST 21.113-88 System of project documentation for construction. Characteristics of accuracy
GOST 21.114-95 Project documentation system for construction. Rules for performing draft drawings of common types of non-type products
GOST 21.302-96 Project documentation system for construction. Conditional graphics symbols in engineering and geological research documentation
GOST 21.408-93 System of project documentation for construction. Rules for performing working documentation of automation of technological processes
GOST 21.501-2011 System of project documentation for construction. Rules for the fulfillment of working documentation of architectural and constructive solutions
GOST 21.709-2011 System of project documentation for construction. Rules for the fulfillment of working documentation of linear structures of hydromelic systems
Note - When using this standard, it is advisable to check the action of reference standards in the public information system - on the official website of the Federal Agency for Technical Regulation and Metrology on the Internet or on the National Standards Annual Information Signal, which is published as of January 1 of the current year, and on issues of the monthly information pointer "National Standards" for the current year. If the reference standard is replaced, to which the undated link is given, it is recommended to use the current version of this standard, taking into account all changes made to this version. If the reference standard is replaced by a dated reference, it is recommended to use the version of this standard with the above-mentioned approval (adoption). If, after approval of this standard in the reference standard, to which the dated reference is given, the change has been made affecting the provider to which the link is given, this provision is recommended to be applied without taking into account this change. If the reference standard is canceled without replacement, the position in which the reference is given to it is recommended to be applied in a portion that does not affect this link.
3 Terms, Definitions and Reducing
3.1 Terms and Definitions
In this standard, the terms of software are applied, GOST R 21.1001, GOST R 21.1002, GOST R 21.1003, as well as the following terms with the corresponding definitions:
3.1.1 main inscription: A combination of information about the project document contained in the columns of the table of the installed form placed on sheets of project and working documentation.
3.1.2 the main set of work drawings: A graphical document containing the necessary and sufficient information in the form of drawings and schemes intended for the production of construction and installation works of a certain type (mark).
3.1.3 full set of working documentation: The combination of the main sets of the work drawings necessary for the construction of a building or structure, complemented by the attached and reference documents.
3.1.4 brand: The letter or alphanumeric index entering the designation of working documentation and determining its attitude to a certain type of construction and installation work, or denoting the main distinguishing features of building structures and their elements.
3.1.7 nepical product: The product (design, device, mounting unit) of technological systems, internal and external systems and networks of engineering and technical support of buildings and structures, first developed and manufactured, as a rule, on the installation site (in the procurement workshop of the assembly organization).
3.1.12 equipment: Technological equipment (machines, apparatus, mechanisms, lifting and other technical means providing the appropriate technological process), as well as engineering equipment of buildings and structures, ensuring safe and favorable conditions for people's vital activity.
3.1.14 plan: Top view or horizontal section of a building or structure.
3.1.15 facade: Orthogonal projection of the outer wall of the building or facilities on the vertical plane.
Note - the facades of the main, side, yard, etc. differ.
3.1.20 designation: Props of the document, which is its identification (distinctive) index.
Note - Each document is assigned the designation, which is recorded in the established places (in the main inscriptions, on title sheets, etc.).
3.2 Abbreviations
This standard uses the following abbreviations:
DE - electronic document;
ECCD - a unified system of design documentation;
CAD - automated design system (systems);
SPDS - a system of project documentation for construction;
SED - system (system) of electronic document management.
4 General requirements for the composition and acquisition of project and working documentation
4.1 Project documentation
4.1.1 The composition of the project documentation of capital construction facilities and the requirements for its content are established by the legislation approved by the Government of the Russian Federation by the provision and regulatory acts of federal executive bodies.
Project documentation is equipped, as a rule, according to individual sections and subsections established by the Regulation. The names and ciphers of the project documentation sections are given in Tables A.1 and A.2 (Appendix A).
In paper form, project documentation is equipped in volumes in accordance with 4.1.4, 4.1.5 and section 8.
With a large volume (in paper form) of the partition or subsection, as well as, if necessary, in other cases (for example, when attracting subcontractors), it is allowed to divide it into parts, and parts, if necessary, on books. Each part and book are completed separately. All parts and books give names reflecting the content of parts or books. Subsections, parts and books are assigned by the sequence numbers of Arabic numbers within, respectively, the partition, subsection or part.
4.1.2 Each partition, subsection, parts and, if necessary, the book complied with, as well as each text and graphical document included in the Self-denotation, which indicates the cover, the title page and / or in the main inscription, as well as in footer columns of text documents performed without major inscriptions.
4.1.3 The designation of the section includes a basic designation set by the system in effect in the project organization, and through a hyphen * - code documentation section. The basic designation includes, for example, a contract number (contract) and / or construction object code (digital, alphabetic or alphanumeric). The basic designation is allowed to include other codes used in CAD and EDS.
_______________
* In the designation, it is allowed to use other separation signs, such as a point, inclined line, and the like.
If the partition is divided into parts, the part designation is made up of the designation of the partition to which the part number is added.
Examples
1 2345-PZ - section 1. Explanatory note.
2 2345-ROM1 - Section 2. Scheme of the planning organization of the land plot. Part 1. General.
3 2345-ROM2 - Section 2. Scheme of the planning organization of the land plot. Part 2. Solutions for internal rail transport.
If the part is divided into books, the designation of the book is from the designation of the part to which the book number is added through the point.
The designation of the subsection is made up of the designation of the section to which the subsection number is added.
If the subsection is divided into parts, the designation of the part is made up of the designation of the subsection to which the part number is added via the point. If the part is divided into books, the designation of the book (if necessary) is made up of the part of the part to which the book number is added through the point.
Examples
1 2345-IOS4.1.1 - section 5. Information about engineering equipment, engineering and technical support networks, a list of engineering and technical measures, the content of technological solutions. Subsection 4. Heating, ventilation and air conditioning, thermal networks. Part 1. Heating, ventilation and air conditioning. Book 1. Basic solutions.
2 2345-IOS4.1.2 - section 5. Information about engineering equipment, engineering and technical support networks, a list of engineering and technical measures, the content of technological solutions. Subsection 4. Heating, ventilation and air conditioning, thermal networks. Part 1. Heating, ventilation and air conditioning. Book 2. Systems of automation of heating, ventilation and air conditioning.
3 2345-IOS4.2 - section 5. Information about engineering equipment, engineering and technical support networks, a list of engineering and technical measures, the content of technological solutions. Subsection 4. Heating, ventilation and air conditioning, thermal networks. Part 2. Thermal networks.
Based on provisions 4.1.1-4.1.3, 4.2.3-4.2.7. used CAD and SED.
4.1.4 Text and graphic materials included in the general case are completed in the following order:
Cover;
Title page;
The statement "The composition of the project documentation".
Note - it is allowed not to include the statement of the "composition of the project documentation" in the composition of each volume, but to equip it with a separate volume;
Text part;
Graphic part (drawings and schemes).
The rules for designing the cover, the title list, the content of volume and the statement "The composition of the project documentation" are shown in section 8.
4.1.5 The number of sheets included in that is determined from the need to ensure the convenience of work, as a rule, not more than 300 sheets of A4 format according to GOST 2.301 or the equivalent number of sheets of other formats.
4.1.6 General requirements for the execution of graphic documentation are given in section 5.
4.1.7 Text documents containing mainly solid text (including text part parts and project documentation subsections) are performed according to GOST 2.105, taking into account 5.1, 5.2 of this standard.
4.1.8 It is allowed to perform the text documents specified in 4.1.7, without major inscriptions, additional graph to them and the framework. In this case:
On the first sheet, lead a list of performers, which indicates positions, initials and surnames of persons who participated in the development, control and coordination of a text document, and provide places for signatures and dates of signing. On the second and, if necessary, the subsequent sheets place the content (table of contents), which includes numbers (designations) and the names of sections, subsections and text document applications indicating sheet numbers (pages);
At the top of the (top footer) of each sheet indicate the designation of the document: in the left corner (with one-sided print) or the right corner of the even pages and the left corner of odd pages (with double-sided printing);
At the bottom of the (lower footer) of each sheet indicate: the logo and name of the organization that prepared the document, the name of the document, the number of the sheet (pages) of the document (in the lower right corner - with one-sided seal or in the left corner of the even pages and the right corner of odd pages - Two-way printing), as well as, if necessary, the version number of the document, the identifier (name) of the file and other information. The logo is allowed and the name of the organization to bring in the top footer;
Change data indicate in accordance with 7.3.
4.1.9 Calculations of constructive and technological solutions, which are a mandatory element of the preparation of project documentation, are not included in the design documentation. They are issued in accordance with the requirements for text documents and are stored in the archive of the project organization. Calculations submit to the Customer or Expertise Authorities on their requirement.
4.2 Working documentation
4.2.1 The working documentation transmitted to the Customer includes:
Workers drawings combined into the main sets of work drawings on stamps. The brands of the main sets of work drawings are shown in Table B.1 (Appendix B);
The accompanying documents developed in addition to the working drawings of the main kit.
4.2.2 The main sets of work drawings include general data on working drawings, drawings and schemes provided for by the relevant SPDS standards.
4.2.3 The main set of work drawings of any brand can be divided into several basic sets of the same brand (with the addition of the sequence number) in accordance with the process of organizing construction and installation work.
Example - AR1; AR2; Kzh1; Kzh2.
4.2.4 Each basic set of work drawings is assigned the designation, which includes the basic designation, installed on the system being operating in the organization, and through the hyphen - the brand of the main kit.
Example - 2345-12-AR,
where 2345-12 is the basic designation. The basic designation includes, for example, the contract number (contract) and / or the construction object code (see 4.1.3), as well as the building number or structure by the master plan *;
_______________
* For working drawings of linear structures, master plan, outdoor communications, this part of the base designation is excluded or replaced by zeros.
Ar is the brand of the main set of work drawings.
4.2.5 It is allowed to form a basic set of work drawings with individual documents with the assignment of the designation consisting of the basic designation, the brand of the main kit, and by adding the Arabic figures through the point number.
Example - 2345-12-EO.1; 2345-12-EO.2,
where 2345-12 is the basic designation;
EO - brand of the main set of work drawings;
1, 2 - sequence numbers of documents of the main set of work drawings.
The first document with such registration of the main set of work drawings should be general data on working drawings.
4.2.6 The attached documents include:
Working documentation for construction products;
Sketch drawings of common types of non-type products performed in accordance with GOST 21.114;
Specification of equipment, products and materials performed in accordance with GOST 21.110;
Polls and overall drawings performed in accordance with the manufacturers (suppliers) of equipment;
Local estimate;
Other documents stipulated by the relevant SPDS standards.
The specific composition of the accompanying documents and the need for their implementation are set by the relevant SPDS standards and the design task.
The accompanying documents design organization conveys the Customer simultaneously with the main set of work drawings in the amount established for the work drawings.
4.2.7 Each accompanying document assign the designation of the main kit with the addition of an enclosed document through the cipher. Encipers of the attached documents are shown in Table B.1 (Appendix B).
Example - 2345-12-EO,
where 2345-12-EO is the designation of the main set of work drawings;
C - cipher specification of equipment, products and materials.
If there are several attached documents of one species to their designation, a sequence number or, through a hyphen, a product brand (for product drawings) is added.
Example - 2345-12-VK.N1; 2345-12-VK.N2, 2345-12-KZH.I-B1, 2345-12-KZH.I-B2
4.2.8 In the working drawings, it is allowed to use typical building structures, products and nodes by references to documents containing workers drawings of these structures and products. Reference documents include:
Standards that include drawings intended for the manufacture of products;
Drawings of typical designs, products and nodes *.
_______________
* If necessary, drawings of typical designs, products and nodes are recorded in the "Accellenged Documents" section (as a rule, without changing the designation) and transferred to the Customer in accordance with 4.2.6.
Reference documents are not included in the working documentation transmitted to the customer. The project organization, if necessary, transmits them to the customer under a separate agreement.
4.2.9 Form, rules for the implementation and designation of the document, which provides the composition of all working documentation made in accordance with the Treaty, are established in the standards of the organization.
4.3 General data on working drawings
4.3.1 In the first sheets of each main set of work drawings, general data on working drawings are included in which include:
The statement of working drawings of the main kit performed in form 1;
The statement of reference and accompanying documents performed in form 2;
The statement of the main sets of work drawings performed in form 2;
The statement of specifications (if there is mainly a set of several location schemes), performed in form 1;
The symbols not established by national standards and the values \u200b\u200bof which are not indicated on other sheets of the main set of work drawings;
General instructions;
Other data provided for by the relevant SPDS standards.
Forms 1 and 2 with instructions for completing them are given in Appendix G.
4.3.2 The statement of working drawings of the main kit contains a sequential list of sheets of the main kit.
When designing a basic set of work drawings with separate documents (see 4.2.5) instead of the statement of the working drawings of the main kit, includes the statement of the documents of the main kit in form 2, and in each of the subsequent documents of the main kit leads links to general data on working drawings .
4.3.3 The report of reference and the accompanying documents are partitions:
Reference documents;
Attached documents.
The "Reference Documents" section indicates documents according to 4.2.8. At the same time, in the respective graphs, the statements indicate the designation and name of the series and the release number of the drawings of typical structures, products and nodes or the designation and name of the standard.
The "Accellenged Documents" section indicates documents according to 4.2.6.
4.3.4 The statement of the main sets of work drawings leads on sheets of general data of one of the main sets of work drawings of the building or structure (at the discretion of the person responsible for developing working documentation). The statement contains a consistent list of the main sets of work drawings, which are part of the full set of working documentation for the building or construction.
If there are several main kits of the working drawings of the same brand (see 4.2.3), they constitute the statement of sets of this brand in form 2 (Appendix D), which is usually given in the general data of each of these sets.
4.3.5 In general directions, lead:
Information about the documents on the basis of which a decision was made on the development of working documentation (for example, a task for designing, approved project documentation);
Recording on the conformity of working documentation The task of design issued by the technical conditions, the requirements of current technical regulations, standards, arrangements of rules, other documents containing established requirements;
A list of technical regulations and regulatory documents containing requirements for technical solutions and further work of work, references to which are given in working drawings;
The absolute mark, accepted in the working drawings of the building or construction conditionally for zero (as a rule, leads to the drawings of architectural and design solutions);
Recording on the results of a patentability and patent purity for the first time used in the project documentation of technological processes, equipment, structures, products and materials, as well as patent numbers and applications for which decisions are made on issuing patents to the inventions used in the working documentation (if necessary);
The list of types of work that affect the safety of the building or structure and for which it is necessary to compile acts of examination of hidden work, responsible structures and sections of engineering and technical support networks;
Information about who owns this intellectual property (if necessary);
Operational requirements for a designed building or building (if necessary);
Other necessary instructions.
In general guidelines, it should not be repeated technical requirements placed on other sheets of the main set of work drawings, and give a description of the technical solutions adopted in the working drawings.
Points of general instructions must have through numbers. Each point of general instructions are recorded from a new line.
5 General Rules for the implementation of documentation
5.1 General
5.1.1 When performing project and working documentation, as well as reporting technical documentation for engineering surveys for construction should be guided by the provisions of the SPDS and ECC standards.
The list of ECC standards subject to accountable in the implementation of graphic and text documentation for construction is given in Table D.1 (Appendix D).
5.1.2 Documentation is typically carried out by an automated manner on paper (in paper form) and / or in the form of DE.
Documents of one type and name, regardless of the method of execution, are equal and interchangeable. Mutual compliance between documents in electronic and paper forms provides a developer.
General requirements for electronic documents - according to GOST 2.051.
5.1.3 In the graphic documents of the image and the conditional designations are performed by lines of the graveyard 2.303. It is allowed to use lines of other types, names, drawing, thickness and main purpose of which are installed in the relevant SPDS standards.
5.1.4 In graphic documents, the conditional designations should be carried out in the main black color. Some conditional designations or their individual elements are allowed to be performed by other colors. Instructions on the color of the symbols are given in the relevant SPDS standards. If the color of the symbols used in the drawings and diagrams are not installed in the standards, their purpose indicates the drawings.
In the scripts intended for the manufacture of black and white copies, colored conditional notation and their elements should be performed in black.
5.1.5 When performing graphic documents, fonts according to GOST 2.304 are used, as well as other fonts used by the means of computing technology, while providing the availability of these fonts to users of documents.
5.1.6 The drawings are performed at an optimal scale according to GOST 2.302, taking into account their complexity and saturation of information.
The scales of images do not indicate the drawings, with the exception of drawings of products and other cases provided for in the relevant SPDS standards. In these cases, the scale is indicated in parentheses immediately after image names in accordance with GOST 2.316 (clause 4.19).
5.1.7 Drawings on paper and electronic drawings (2D) can be performed on the basis of an electronic model (3D) building or structures (GOST 2.052).
5.1.9 The structure and composition of DE details should provide its appeal within software (display, making changes, printing, accounting and storage in databases, as well as transmitting to other automated systems) in addition to regulatory requirements for paperwork.
5.1.10 For consideration, coordination, expertise and approval are copies of documents of project and working documentation, compiled, as indicated in 4.1 and 4.2.
5.1.11 The form of presentation of documents of project and working documentation (paper or electronic), if it is not specified in the design task, is determined by the developer in coordination with the customer. It is allowed to include in the design and working documentation documents in various forms of submission.
5.1.12 The rules for the transfer of documentation on electronic media, including the nomenclature and forms of the necessary accounting and reporting documents, establish in the standards of the organization developed on the basis of GOST 2.051, GOST 2.511 and GOST 2.512.
5.1.13 The list of cuts of words allowed in graphical documents is compiled in addition to GOST 2.316 and is shown in Table E.1 (Appendix E).
5.2 Main inscriptions
5.2.1 Each sheet of graphic and text document, as a rule, is drawn up the main inscription and additional graphs to it. Forms of the main inscriptions and instructions on their completion are given in Appendix J.
Note - The main inscriptions do not make up text documents performed in accordance with 4.1.8, estimates, etc.
The main inscription is placed in the lower right corner of the sheet.
On A4 sheets according to GOST 2.301, the main inscription is placed along the short side of the sheet. For text documents in tabular form is allowed, if necessary, have the main inscription along the long side of the sheet.
On sheets of basic sets of work drawings and sheets of the graphic part of the project documentation - form 3;
On the first sheet of drawings of construction products - form 4;
In the first or title * sheets of text documents and the first sheets of sketch drawings of common types of non-type products, designed in the form of release, - form 5;
_______________
* For text documents performed with the title list and the main inscriptions are made, the top is the next sheet after the title leaf.
On the subsequent sheets of drawings of construction products, text documents and sketch drawings of general species - form 6.
The first sheet of the drawing of the construction product is allowed to design the main inscription in form 5.
5.2.3. If some text documents (for example, the specification of equipment, products and materials) are produced without a title list, then in this case the first sheet of the document is issued by the main inscription in form 3, subsequent - in form 6.
When making the main set of work drawings with separate documents, documents containing solid text and / or in the form of tables (for example, general data, cable log, etc.) are issued as text documents. In this case, the first sheet of the document is drawn up by the main inscription in form 3, subsequent - in form 6.
5.2.4 In the reporting technical documentation on the results of engineering surveys, the main inscription is used:
On sheets of graphic documents used in the design as a basis - in form 3;
In the first sheets of other graphic and text documents - in form 5, on subsequent sheets - in form 6.
5.2.5 The main inscription, additional graphs for it and the framework are performed by solid thick basic and solid thin lines according to GOST 2.303.
5.2.6 Table of changes in the main inscription (column 14-19), if necessary, allowed to continue up or left from the main inscription. When the table of change table is located on the left of the main names of the name, the graph 14-19 is repeated.
5.2.7 Location of the main inscription and additional graph to it, as well as the size of the frames on the sheets are shown in Figures and.1 and and.2 (Appendix and).
5.2.8 Location and dimensions of additional graph for identification of DE Project organization establishes independently.
5.2.9 It is allowed to additionally identify project documents using bar code.
At the same time, the document designation, version number and the designation of the document should be used as a barcode details. Additionally, the country code, the code of the developer and other details can be used.
5.3 Coordination axes
5.3.1 On the images of the building or structure, the coordination axes of its supporting structures are indicated, intended to determine the mutual arrangement of elements of the building or building and binding a building or structure to a construction geodetic grid or a center base.
5.3.2 Each individual building or construction is assigned an independent system for the coordination axes.
Coordination axes are applied to the images of the building, facilities with thin barcccotted lines with long strokes, denoted in the circles with a diameter of 6-12 mm Arabic numbers and the capital letters of the Russian alphabet (with the exception of letters: E, s, th, o, x, c, h, u , Ъ, s, b) or, if necessary, letters of the Latin alphabet (with the exception of letters I and O).
Skipping in digital and letter (except indicated) designations of coordination axes are not allowed.
The figures indicate the coordination axes on the side of the building and facilities with a large number of axes. If there is not enough alphabet letters to designate the coordination axes, the subsequent axes are denoted by two letters.
Example - AA, BB, BB.
5.3.3 The sequence of the coordination axes are taken according to plan, as shown in Figure 1 but: Digital axes - from left to right, alphabetic axes - bottom-up or as shown in Figures 1 b. and 1 in.
Picture 1
5.3.4 The designation of the coordination axes is usually applied to the left and lower parties of the plan of the building and facilities.
If the coordination axes of the opposite sides are incomprehensible, the plan in the locations of discrepancies additionally apply the designations of the specified axes over the top and / or right parties.
5.3.5 For individual elements located between the coordination axes of the main supporting structures, additional axes are applied to which the designation is assigned in the form of a fraction, in the numerator of which indicate the designation of the preceding coordination axis, and in the denominator - an additional sequence number within the section between the adjacent coordination axes in according to Figure 1 g..
It is allowed by the coordination axes of the half-timbered columns to assign digital and alphabetic designations to the continuation of the designations of the axes of the main columns without an additional number.
5.3.6 In the image of a repeated element affected by several coordination axes, coordination axes are denoted in accordance with the picture:
2but - with their number of no more than 3;
2b. - with their number of more than 3;
2in - With all alphabetic and digital coordination axes.
Figure 2.
If necessary, the orientation of the coordination axis, to which the element is tied to the adjacent axis is indicated in accordance with Figure 2 g..
5.3.7 On the plans of residential buildings arranged from block sections, the extreme coordination axes of the block sections are assigned notation according to 5.3.1-5.3.3, which indicate in accordance with Figure 3 but.
Figure 3.
The coordination axes of block-sections, including extreme, assign independent notation according to 5.3.1-5.3.3 with the addition of the "C" index (see Figure 3 b.). If necessary, on the plan of the block section indicate the designations of the coordination axes of the building composed from the block sections.
5.3.8 Three-dimensional (3D) electronic model of a building or facilities are performed in a single planning and high-rise coordinate system.
The coordinate system of the three-dimensional model of the building or structures is depicted in three mutually perpendicular lines with the beginning of the coordinates located at the point of intersection of axes 1 and and on the zero mark of this building or structure in accordance with Figure 4.
Figure 4.
At the same time, for a rectangular building (see Figure 1 but) For a positive direction, assume: axis - in the direction of increasing the digital designations of the coordination axes, the axis - up to increase the letter designations of the coordination axes, the z axis - vertically upward from the conditional zero mark of the building.
5.4 Drawing, slopes, marks and inscriptions
5.4.1 Linear dimensions in drawings indicate without the designation of length units:
In meters up to two places after the communion - in the drawings of external networks and communications, master plan and transport, except in cases specified in the relevant SPDS standards;
In millimeters - on all other types of drawings.
5.4.2 Dimensional line at its intersection with remote lines, contour lines or axial lines are limited by serifs 2-4 mm long, applied with a slope to the right at an angle of 45 ° to the dimensional line, while the dimensional lines continue for extreme remote lines (or respectively Contour or axis) by 0-3 mm.
When applying the size of the diameter or radius inside the circle, as well as the angular size of the dimension line is limited by arrows. Arrows are also used when applying the sizes of radii and internal rounds.
When drawing dimensions on axonometric schemes of technological pipelines and engineering systems, dimensional lines are allowed to be limited by arrows.
5.4.3 levels of levels (heights, depths) of structural elements, equipment, pipelines, air ducts, etc. From the reference level (conditional "zero" mark) indicate in meters without designating a unit of length with three decimal signs separated from an integer comma for The exception of the cases specified in the relevant SPDS standards.
Level marks on the facades, cuts and sections are placed on remote lines (or on the loop lines) and denote the sign "", performed by solid thin lines with a length of the strokes 2-4 mm at an angle of 45 ° to a remote line or contour line, according to the pattern five; On plans - in a rectangle in accordance with Figure 6, with the exception of cases specified in the relevant SPDS standards.
Figure 5.
Figure 6.
The "zero" mark received, as a rule, for the surface of a building of a building or structure, located near the planning surface of the Earth, indicate without a mark; The relative marks above zero indicate with the "+" sign, below zero - with the sign "-".
Note - As a zero mark for buildings, as a rule, the level of pure floor of the first floor is taken.
5.4.4 On the plans, the direction of the plane slope indicate the arrow over which, if necessary, affix the numeric value of the slope in percent in accordance with Figure 7 but or in the form of a relationship of the altitude of the plane to the corresponding horizontal projection (for example, 1: 7).
Figure 7.
The numeric value of the slope is allowed in the ppm or in the form of a decimal fraction with an accuracy of the third mark.
At cuts, sections and schemes before the dimensional number that determines the numerical value of the slope, the sign "", the sharp angle of which should be directed towards the slope (except for the rescalation of embankments and recesses). The designation of the slope is applied directly above the line of the contour or on the shelf of the liner lines in accordance with Figure 7 b..
5.4.5 Rooms of positions or stamps of elements are applied on the shelves of lines-carrying, conducted from images of elements of structures of buildings or structures, next to the image - without a lifting line or within the contours of the pictures of the elements in accordance with Figure 8.
Figure 8.
Truck line, as a rule, finish with a point. If the lifting line is assigned to the line indicating the surface, then it is completed with the arrow. With a small-scale image, the lifting line finish without arrow and point.
5.4.6 Remote inscriptions to multilayer structures are performed in accordance with Figure 9.
Note - figures are conditionally indicated by the sequence of layers of structures and inscriptions on the shelves of lines.
Figure 9.
5.4.7 The font size for referring to the coordination axes, positions (grades), names and image designations should be 1.5-2 times larger than the size of the number of dimensional numbers used in the same graphical document.
5.5 Images (cuts, sections, species, remote elements)
5.5.1 Images in the drawings are performed in accordance with GOST 2.305, taking into account the requirements of this standard and other SPDS standards.
5.5.2 Sections of buildings or structures are denoted by Arabic numbers sequentially within the graphical document. Sections are denoted in the same way.
Note - In the drawings of the project and working documentation, the incision is called, as a rule, a vertical section of a building or structure, i.e. A section made by a securing plane perpendicular to the horizontal plane of projections.
Self-numbering is allowed for cuts and sections of individual sections of the building, structures or installations, all the drawings of which are located on one sheet or sheets of sheets and if there are no references to cuts and sections on these drawings located on other sheets of graphics document.
It is allowed to designate cuts by the capital letters of the Russian alphabet, and the sections - the capital or lower case letters of the Russian alphabet (with the exception of the letters specified in 5.3.2).
The position of the secular plane indicates the drawing of the cross section line (open line 2.303 linte). With a complex section, the strokes are also carried out in the intersection of the sequential planes among themselves. On the initial and finite strokes should be put the arrows indicating the direction of the view; Arrows should be applied at a distance of 2-3 mm from the end of the stroke (Figure 10).
Figure 10.
The direction of the view for a cut according to the plan of the building and facilities takes, as a rule, from the bottom up and right to left.
5.5.3 If separate parts of the form (facade), the plan, the cut require a more detailed image, then further perform local species and remote elements - nodes and fragments.
5.5.4 In the image (plan, facade or section), from where the node is made, the corresponding place is noted by a closed solid thin line (circumference, an oval or a rectangle with rounded corners) with applying the line-taking line shelf the designations of the Arabic node in accordance with Figures 11 but, 11b. or the capital letter of the Russian alphabet in accordance with Figure 11 in.
Figure 11.
If you need to link to the node placed in another graphic document (for example, the main set of work drawings), or on the working drawings of the typical construction site indicate the designation and number of the list of the corresponding document in accordance with Figure 11 b. Or a series of working drawings of typical nodes and a release number in accordance with Figure 11 in.
Figure 12.
Above the image of the node indicate the mug of its designation in accordance with Figure 13 butif the node is depicted on the same sheet where it is made, or 13 b.if he is put on another sheet.
Figure 13.
An assembly that is a complete mirror reflection of another (main) execution is assigned the same designation as the main execution, with the addition of the "N" index.
5.5.5 Local species indicate the capital letters of the Russian alphabet, which are applied next to the arrow indicating the direction of the view. The same designations are applied to images of species.
5.5.6 For each type of images (cuts and sections, nodes, fragments), an independent numbering order is used or alphabetic designations.
5.5.7 In the image (plan, facade or section), from where a fragment is taken out, the corresponding place is noted, as a rule, a figure bracket in accordance with Figure 14.
Figure 14.
The name and sequence number of the fragment are applied under the curly bracket or on the shelf of the lifting line, as well as above the corresponding fragment.
5.5.8 Images to the axis of symmetry of symmetric plans and facades of buildings and structures, arrangement of structural elements, plans for the location of technological, energy, sanitary and other equipment are not allowed.
5.5.9 If the image of the cut, section, node, type or fragment is placed on another sheet, then after designation, the number of this sheet is indicated in brackets in accordance with Figures 10, 11 but, 12 and 14.
5.5.10 Images allowed to rotate. At the same time, in the names of images in the drawings, the conditional graphical designation "rotated" according to GOST 2.305, if the position of the image is defined uniquely, i.e. Oriented by coordination axes and / or high-altitude marks.
5.5.11 If an image (for example, a plan) does not fit on a sheet of adopted format, it is divided into several sections by placing them on separate sheets.
In this case, on each sheet, where the image section is shown, lead a scheme of a whole image with the necessary coordination axes and the symbol (shading) of the image section shown on this sheet in accordance with Figure 15.
Note - If the drawings of the image sections are placed in different basic sets of work drawings, then over the sheet number indicates a complete designation of the corresponding main kit.
Figure 15.
5.5.12 If the plans of the floors of a multi-storey building have small differences from each other, then fully implement the plan of one of the floors, for other floors, only those parts of the plan are performed to show the difference from the plan shown in full.
Under the name of the partially depicted plan, write: "The rest, see the Plan (name of the fully depicted plan)".
5.5.13 In the names of the plans of the building or structure, the word "plan" and the netting of the clean floor or the floor number, or the designation of the appropriate secular plane (when performing two or more plans at different levels within the flood).
Examples
1 Plan for OTM. 0,000
2 Plan 2 floors
When performing a part of the plan in the title indicate axes that limit this part of the plan.
Example - Plan for Options. 0,000 between axes 21-30 and a-d
It is allowed in the name of the floor plan to indicate the purpose of the premises located on the floor.
5.5.14 In the names of the building cuts (structures), the word "incision" and the designation of the corresponding section of the plane is 5.5.2.
Example - section 1-1
Note - In the names of products, the word "incision" does not indicate.
The names of the sections are digital or alphabetic designations of the sequential planes.
Example - 5-5, BB, Aaa
5.5.15 In the names of the facades of the building or structures, the word "facade" and the designations of the extreme axes, between which the facade is located.
Example - Facade 1-12, Facade 1-1, Facade A-G
It is allowed in the name of the facade to indicate its location, for example, "the main", "yard", etc.
5.5.16 The names of images are not emphasized in the drawings.
6 Rules for performing specifications in the drawings
6.1 To the layout of the elements of the collection structure, monolithic reinforced concrete design, to the drawings of the production equipment and / or pipelines, installations (blocks) of technological, sanitary and other equipment, and other drawings are specification in form 7 (Appendix K).
When performing drawings, the group method constitutes group specifications in form 8 (Appendix K).
6.2 The specification is placed, as a rule, on the list of drawings, where the schemes, plans for the location of equipment and pipelines, installation plans are depicted. It is allowed to perform the specification on separate sheets as the subsequent sheets of drawings.
6.3 In electronic models, if necessary, specifications and other tables in the drawings are allowed to be performed in the working space of the electronic model, taking into account the provisions of GOST 2.052. In this case, they are recommended to perform in a separate information level.
6.4 Specifications of construction products are according to GOST 21.501.
7 Rules for making changes
7.1 General
7.1.1 On the basis of the provisions of Section 7 of this Standard, standards of organizations that take into account the features of making changes to project documents will be developed depending on the amount of documentation, the conditions of document management and the CAD and the SED used.
7.1.2 Changing the document previously transferred to the customer is any correction, exception or adding any data to it without changing the designation of this document.
The designation of the document is allowed to change only when different documents are erroneously assigned the same designations or an error is made in the designation.
Making changes to calculations is not allowed.
7.1.3 If a change in the document is unacceptable, a new document with a new designation must be released.
7.1.4 Any change in the document that causing any changes in other documents should simultaneously be accompanied by the introduction of appropriate changes to all interconnected documents.
7.1.5 Changes contribute to the original document.
7.1.6 The fact information change information indicates:
In paper documents - in the main inscription of these documents and / or in the Change Registration Tables;
In DE - in the detailed part of these documents;
In the column "Note" of documents and statements intended for accounting for documents.
7.2 Permission to make changes
7.2.1 Changing the document (including canceled it) is carried out, as a rule, based on permission to make changes (hereinafter - permission). Permission is performed on paper forms 9 and 9a (application L) or as DE.
The resolution is registered in accordance with GOST R 21.1003.
7.2.2 Permission approves the head of the organization - a document developer or another official authorized.
The resolution is the basis for receiving the original documents and the changes in them.
7.2.3 The scripts of permits on paper are stored in the archive of the organization.
7.2.4 Changes to each document (for example, the main set of work drawings, the specification of equipment, products and materials) are made on the basis of a separate resolution.
It is allowed to make one general permission to change, introduced simultaneously in several documents if the changes are interconnected or the same for all changeable documents.
Changes to the documents of the main set of work drawings decorated with separate documents (see 4.2.5), as well as documents of the Tom of Project Documentation are made on the basis of one general permission.
7.2.5 When making changes to DE, permission is allowed not to do, if the CAD and the EDD accounts and storing the versions of the document and the access control is ensured, excluding the possibility of unauthorized changes.
7.3 Amendments
7.3.1 Changes denote by sequence numbers (1, 2, 3, etc.). One sequence number of the Change is assigned to all changes that contribute to the document in one permission. It is indicated for the whole document, regardless of how many sheets it is completed.
7.3.2 When making changes to the DE script, any change is indexed as a new version of this document.
7.3.3 Changes in paper scripts of documents contribute:
Crossing;
Clearing (washing);
Painting with white;
Introduction of new data;
Replacement of sheets or all the document;
Introducing new additional sheets and / or documents;
Except for individual sheets of the document.
At the same time take into account the physical state of the original.
7.3.4 Changes to documents are made by automated and handwritten methods.
7.3.5 The handwritten method of change is made in paper scripts of documents in accordance with 7.3.9-7.3.16.
After making, the original should be suitable for making copies of the documentation of the appropriate quality methods of reprogram.
7.3.6 Making changes to DE produced by issuing a new version of a document with changes.
7.3.7 When making changes to an automated method, a new script is manufactured taking into account the changes made and retain its former designation.
The new script is also manufactured if there is not enough place for handwriting changes or a violation of the image clarity is possible when corrected.
If one or several sheets of the script is replaced or add or add, then they retain the inventory number assigned to the script.
When replacing all the script sheets, he is assigned a new inventory number.
7.3.8 Changes to the estimated documentation are carried out by an automated way to replace the entire document.
7.3.9 Changeable sizes, words, signs, inscriptions, etc. Excrying with solid thin lines and there are new data.
7.3.10 When the image is changed (part of the image), it is reduced by a solid thin line forming a closed circuit, and crucifically crossed with solid thin lines in accordance with Figure 16.
Figure 16.
A new image of the changed area is performed on a free field of a sheet or on another sheet without turns.
7.3.11 A variable and additional sections of the image are assigned a designation consisting of a sequence number of the next document change and through the point of the sequence number of the variable (optional) portion of the image within this sheet. In this case, the new image of the changed area is assigned the designation of the changed image.
If a new image of the changed area is placed on another sheet, the changes assigned to it is preserved and in the table of changes of this sheet do not take into account.
7.3.12 Near each change, including near the space fixed by the cleaner (wash) or inks with white, outside the image or text is applied in the parallelogram the designation of the change (see Figure 16) and from this parallelogram conduct a solid thin line to the changed area .
It is allowed from the parallelogram with the designation of the change of the line to the changed area not to be carried out.
When making changes to text documents (in the text part of the documents), the line from the parallelogram is not carried out with the designation.
7.3.13 Closely located from each other modified sizes, words, signs, inscriptions, etc. They will be reduced with a solid thin line, forming a closed loop, without more crossing in accordance with Figure 17.
Figure 17.
7.3.14 If a new image of the modified area is placed on another sheet, then the replaced image also indicates the number of the leaf on which the new image is located (see Figure 16).
7.3.15 Over the new image of the modified area is placed in the parallelogram the designation of the change in the replaced image, and at a parallelogram indicate: "In return crushed."
If a new image of the modified area is placed on another sheet, then at a parallelogram indicate: "In addition to the listed on the sheet (the sheet number on which the image is replaced)" in accordance with Figure 18.
Figure 18.
7.3.16 If a new image of the changed area is placed near the replaced, they are connected by liners with the notation with the designation of the change in accordance with Figure 19.
Figure 19.
Over the optional image is placed in the parallelogram the designation of the change, and at the parallelogram indicate: "Supplement" in accordance with Figure 20.
Figure 20.
7.3.17 When adding a new sheet of a text document, it is allowed to assign the number of the previous sheet with the addition of the next lower case letter of the Russian alphabet or through the Arabic digit point, for example 3a or 3.1.
In text documents containing mainly solid text, it is allowed when adding a new item to assign the number of the previous paragraph with the addition of the next lower case letter of the Russian alphabet, and with the exclusion of the item - to save the numbers of subsequent points.
7.3.18 When the total number of sheets of the document on its first sheet, the corresponding corrections in the Count "Sheets" contribute to the main inscription.
7.3.19 Data on changes made to the original indicate the change table placed in the main inscription (if available), and with a lack of space - in the additional table to it (see 5.2.6).
In the new (modified) version of the DE in the Change table indicate the data only on the last change.
7.3.20 When making changes to the documents, the change table is filled with sheets (sheet):
The first (title) of the new script, made in general instead of the old one;
Modified;
Released instead replaced;
Added again.
7.3.21 The change table indicates:
a) in the column "Izm." - Order number of document change. When replacing the original, the new regular serial number is affixed, based on the last number of the change specified in the replaced script;
b) in the column "count. uch." - the number of variable sections of the image on this sheet within the next change;
c) in the column "Sheet":
1) on sheets released instead of replaced - "deputy";
2) on sheets added again, - "New";
3) when replacing all sheets of the original when manually making changes in the first (title) sheet - "All" (while the table of changes on other sheets of this script does not fill), an automated way - "deputy." On all sheets.
In other cases, the column "Sheet" is puffed;
d) in the column "n dock" - permit designation;
e) in the column "sub." - signature of the person responsible for the correctness of the change. When replacing all the sheets of the original automated method, the signature is affixed only on the first (title) sheet. The signature of the normocontroller is affixed on the field to cover the sheet (except for sheets released instead of replaced and new);
e) in the "Date" column - the date of change.
7.3.22 The registration of changes in text documents is recommended to be carried out in the registration table of changes in form 10 (Appendix M), which is placed on a separate last sheet of document when making the first and subsequent changes.
7.3.23 When replacing sheets of documents issued by the main inscriptions in forms 3-5, the sheets released instead of replaced, sign in graphs 10-13 of the main inscriptions in accordance with the procedure provided for for newly developed sheets.
7.3.24 When canceling or replacing the document sheets on all annulled and replaced sheets of the original stamp, "canceled (replaced)" in the form given in GOST R 21.1003 (Appendix D), which is filled in accordance with the instructions given in the same place.
7.4 Features of making changes to project documentation
7.4.1 Amendments to project documentation are made according to 7.1-7.3, taking into account the provisions 7.4.2-7.4.8.
7.4.2 Changes to the project documentation previously transferred to the Customer, as a rule, make an automated way and implement:
Replacement, adding or exception of individual volume sheets;
Replacement (reissue) volume - with its full processing;
Release of additional volumes.
7.4.3 With the full processing of the section or subsection of project documentation, at the beginning of its textual part, it is recommended to provide information on the changes: the basis for making changes, a brief description of the changes made.
7.4.4 If the changes are made on the basis of a negative conclusion of the project documentation expertise, then the "Explanatory Note" section includes a certificate with a description of the changes made to the project documentation. The certificate must be signed by the person responsible for the preparation of project documentation, the chief project engineer.
7.4.5 Registration of changes (versions) of volumes generally produced in the table of registration of changes in form 11 (Appendix M), which is placed when making changes on its title page and cover. It is allowed to give the table only on the cover.
The state registration table does not take into account the corrections made to the statement "Composition of Project Documentation" in connection with the changes in other volumes of project documentation.
7.4.6 Information on changes in the sheets of graphic documents indicate the column "Note" of the content of volume:
a) For replaced sheets when making a first change - "Changes. 1 (deputy)", subsequent changes - additionally, the next changes numbers, separating them from the previous point with a comma.
An example is changed. 1 (deputy);
b) for eliminated (annulled) sheets in the change number - "(Annun.)".
An example is changed. 1 (Annun.);
c) for additional sheets in the number of change - "(new)"
An example is changed. 1 (new).
7.4.7 When performing additional volumes of project documentation, corrections contribute to the statement of the composition of the project documentation.
Information about the changes in the "Composition of Project Documentation" in the content of volume does not lead.
7.4.8 Changes to the approved project documentation related to the change in the parameters of the construction object affecting its constructive reliability and security, and the need to reaffece project documentation, contribute by the Customer's decision on the basis of a new task for designing or additioning to the previously approved task for design.
7.5 Features of making changes to working documentation
7.5.1 Amendments to working documentation are carried out according to 7.1-7.3, taking into account the provisions 7.5.2-7.5.9.
7.5.2 When making changes to the sheets of the main set of work drawings in the statement of the working drawings of this kit in the "Note" column indicate:
For replaced, canceled and additional sheets - information in accordance with the transfers A) -B) 7.4.6;
For modified sheets (handwritten method) when making a first change - "Change. 1", subsequent changes are additionally the next number of changes, separating them from the previous semicolon.
An example is changed. one; 2; 3.
In case of replacing sheet data sheets in the statement of the working drawings of this kit, it is allowed to provide information only about the last change in the sheets of the main kit.
7.5.3 If additional sheets include additional sheets in the main set of work drawings, then they are assigned the next ordinal numbers and recorded in the continuation of the statement of the work drawings of the corresponding main kit.
With a lack of space in the statement of work drawings for recording additional sheets, the continuation of the statement is transferred to the first of the additional sheets. At the same time, at the end of the statement of the work drawings placed in "General Data", they make an entry: "For the continuation of the statement, see the sheet (sheet number)", and the headline is placed on the checkliness on the additional sheet: "The statement of the work drawings of the main kit (continued) .
When changing the names of the sheets make appropriate corrections in the Count "Name".
When making changes to the handwritten method, the number and names of the canceled sheets in the statement of the working drawings are burned with an automated method - the Count "Name" for the annulled sheets is not filled.
7.5.4 When making changes to the documents of the main kit, decorated with individual documents, appropriate corrections to the statement of documents of the main set of work drawings.
7.5.5 When performing additional and cancellation of previously accompanying documents, corrections are made to the section "The Accellenged Documents" of the Lord of the reference and attached documents of the corresponding major set of work drawings.
When replacing reference documents in the working drawings (see 4.2.8), corrections make corrections to the appropriate section of the Vedomosti reference and the accompanying documents.
7.5.6 When performing additional and cancellation of previously completed main sets of work drawings make corrections to the statement of the main sets of work drawings.
7.5.7 In the tables of changes on sheets of general data, corrections made in the statement of general data in connection with the introduction of changes in the sheets of the main kit and the accompanying documents are not taken into account as plots of changes in accordance with 7.3.11.
7.5.8 Registration of changes in document documents issued by title sheets, also produced in the registration table of changes in form 11 (Appendix M), which is placed on the title page when making changes.
7.5.9 Copies of sheets (modified, additional and released instead of replaced sheets) Working documentation on paper guide are sent to organizations that were previously sent copies of documents, simultaneously with copies of the general data of the relevant basic set of work drawings refined in accordance with 7.5.2-7.5. .6.
In electronic form, organizations guide new versions of documents with changes (see 7.3.6).
8 Rules for issuing discharged documentation
8.1 Copies of textual and graphic materials of project documentation and reporting technical documentation for engineering surveys are brocked in Toms folded on A4 GOST 2.301 format.
Note - Under the stitching it means the placement of materials of project documentation on paper in binding or in solid folders with easy-to-lock mounts (locks).
8.2 Copies of documents of working documentation are equipped with a folder with polist, folded on A4 format, as a rule, separately for the main sets of work drawings.
It is allowed to stroke copies of working documents in the volume in accordance with 8.1 or into albums folded on A3 format.
The number of sheets included in the folder or album must correspond 4.1.5.
8.3 Each document, a volume or album, intended for a brochure, as well as the folder with the documents folded into it, make up the cover in form 12 (Appendix N). The cover is not numbered and not included in the total number of sheets.
8.4 The first sheet of a discharged document, as well as a volume consisting of several documents, an album or folder with working documentation, is a title list.
The title page is performed in form 13 (Appendix P). Examples of the performance of title sheets are shown in Figures P.1 and P.2 (Appendix P).
In the volume of project documentation, consisting of several independent documents, including the text part, the title list to the text part, as a rule, is not executed.
8.5 All sheets of a discharged volume (album) are recommended to numbered through the passage of sheets, starting from the title leaf. At the same time, the title page does not name. The sheet number is indicated in the upper right corner of the sheet of the sheet (see Appendix and).
In addition, text and graphic documents included in the (album) and having an independent designation should have a sequence numbering of sheets within a document with one designation in the main inscription or in footer (in accordance with 4.1.8).
8.6 When you recruit multiple documents in the form of volume, album, as well as in the folder after the title page, the content of the volume (album, folders), which is a list of documents included in that (album, folder). The content is performed in form 2 (application d) on the sheets of A4 format.
Documents in the content are recorded in the sequence of their acquisition in the album or folder. The graphic documents of the project and reporting technical documentation for engineering surveys are written pols. The cover and the title page in the content is not written.
In the Count "Name" - the name of the document in full compliance with the name specified in the main inscription or on the title page;
In the Count "Note" - information about the changes made to the recorded documents, as well as the number of the volume sheet of volume through the passage of volume sheets in accordance with 8.5, from which the document begins.
If the end-toile numbering is not performed, then in the "Note" column, the total number of sheets of each document leads. At the end of the content, there is a total number of sheets included in the (album, folder).
The first sheet of volume content (album, folders) is drawn up the main inscription in form 5 (application g), follow-up - in form 6 (application g). The content is assigned a designation consisting of the volume designation (album, folders) and through the defisis of cipher "C".
Example - 2345-ROM2-C; 2345-11-kzh.i-s; 2345-11-rs.ol-s; 2345-11-TXN
In column 5, the main inscription indicates the "content of the volume" or, accordingly, the "album content" and "folder content" and further - the number of the corresponding volume, album or folder (if available).
8.7 Title sheets of volumetric volume documentation are written in signatures:
Supervisor or chief engineer organization;
Persons responsible for the preparation of project documentation, such as the chief engineer (architect) of the project.
Title sheets of working documents are issued by the signed by the person responsible for the preparation of working documentation, the chief engineer (architect) of the project.
The title page of the technical report on the results of engineering surveys is issued by the signature of the head of the organization or its deputy and, if necessary, other officials.
The title sheets of copies of the documentation transmitted to the customer are assumed by the print print of the organization that prepared this documentation.
8.8 The composition of the project documentation, as well as the composition of the reporting technical documentation on the results of engineering surveys, lead in the statement performed in form 14 (Appendix C) on the A4 sheets.
The statements lead a consistent list of volumes of project or reporting technical documentation for engineering surveys.
The first sheet of statement is drawn up the main inscription in form 5 (Appendix G), follow-up - in form 6 (application g).
The composition of the project documentation is assigned a designation consisting of the basic designation of project documentation and through the defisis of cipher "SP".
Example - 2345-joint
When blocking a statement in a separate volume, it is made in cover and title sheet in accordance with 8.3 and 8.4. The volume number on the cover and the title page does not indicate.
The composition of the reporting technical documentation on the results of engineering surveys is assigned the designation consisting of the basic designation of documentation and through the defisis of the cipher "SD".
Example - 2344-CD
A.1 CIFRES OF STEPS OF THE PROJECT DOCUMENTATIONS ON CAPITAL CONSTRUCTION OBJECTIVES OF PRODUCTION AND ENTERPRISTING DESSIONS Listed in Table A.1.
Table A.1.
|
Section number |
Cipher section |
|
|
Explanatory note |
||
|
Land Planning Organization Scheme |
||
|
Architectural solutions |
||
|
Constructive and volume planning solutions |
||
|
Information about engineering equipment, engineering and technical support networks, a list of engineering and technical measures, the content of technological solutions |
||
|
Project of the organization of work on demolition or dismantling of capital construction facilities |
||
|
List of environmental protection measures |
||
|
Disabled access activities |
||
|
10 |
Requirements for ensuring the safe operation of the capital construction facility |
|
|
Estimation for the construction of capital construction facilities |
||
|
Events to ensure compliance with the requirements of the energy efficiency and requirements of the equipment of buildings, buildings and structures to the instruments of accounting of energy resources used |
||
|
Other documentation established by legislative acts of the Russian Federation |
||
|
Note - the partition numbers 10 and 11 are allowed to bring 10 (1), 11 (1) or 10-1, 11-1. |
||
A.2 Encipers of project documentation sections on linear objects are shown in Table A.2.
Table A.2.
|
Section number |
Name of the project documentation |
Cipher section |
|
Explanatory note |
||
|
Draft Strip Top |
||
|
Technological and structural solutions of a linear object. Artificial constructions |
||
|
Buildings, buildings and structures included in the infrastructure of a linear object * |
||
|
Project organization of construction |
||
|
Project of the organization of work on demolition (dismantling) of a linear object |
||
|
Environmental protection measures |
||
|
Fire Safety Activities |
||
|
Estimation for construction |
||
|
Other documentation in cases provided for by federal laws, including: |
||
|
List of civil defense activities, measures to prevent emergency situations of natural and man-made character, measures to counteract terrorism |
||
|
Declaration of industrial safety of hazardous production facilities |
||
|
Safety Declaration of hydraulic structures |
||
|
* Project documentation of buildings, buildings and structures are developed in accordance with the composition of the documentation on Table A.1. |
||
Note - If necessary, code documentation sections are allowed to be denoted by the letters of the Latin alphabet in accordance with the rules established in the standards of organizations.
Table B.1.
|
Name of the main set of work drawings |
Note |
|
|
General Plan and Transport Construction |
When combining work drawings of the master plan and transportation structures |
|
|
General plan |
||
|
Car roads |
||
|
Railways |
||
|
Construction facilities |
When combining workers' drawings of automotive, iron and other roads |
|
|
Architectural and construction solutions |
When combining work drawings of architectural and design solutions (except KM) |
|
|
Architectural solutions |
||
|
Interiors |
Workers drawings can be combined with the main set of the Arm or AC |
|
|
Constructs are reinforced concrete |
||
|
Metal designs |
||
|
Metal designs detail |
||
|
Wooden designs |
||
|
Hydraulic solutions |
||
|
Anticorrosive protection of buildings, structures |
||
|
Power supply |
||
|
Outdoor electric light |
||
|
Power equipment |
||
|
Electric lighting (internal) |
||
|
Exterior Water Supply Networks |
||
|
Outdoor sewage networks |
||
|
Outdoor network of water supply and sewage |
When combining workers' drawings of external water supply and sewage networks |
|
|
Internal water supply and sewage systems |
||
|
Firefighting |
||
|
Heating, ventilation and air conditioning |
||
|
Air supply |
||
|
Dustovation |
||
|
Fooling |
||
|
Teplomechanical solutions |
Boiler houses, CHP, etc. |
|
|
Heat mechanical solutions of thermal networks |
||
|
Wired communications * |
The names of the main sets and the designations of the brands are taken by Appendix A GOST R 21.1703 |
|
|
Radio communication, broadcasting and television |
||
|
Fire alarm |
||
|
Security and Security and Fire Alarm |
||
|
Outdoor gas pipelines |
||
|
Gas supply (internal devices) |
||
|
Production technology |
||
|
Technological communications |
When combining workers' drawings of all technological communications |
|
|
Anticorrosive protection of technological apparatus, gas ducts and pipelines |
||
|
Thermal insulation of equipment and pipelines |
||
|
Automation complex |
When combining workers' drawings of automation of various technological processes and engineering systems |
|
|
Automation + (**) |
The names of the main sets and the designations of the brands are taken by Appendix A GOST 21.408 |
|
|
Hydrogenic linear structures * |
The names of the main sets and the designations of stamps are taken by Appendix A GOST 21.709 |
|
|
* There are general names of objects. Notes 1 If necessary, additional brands of the main sets of work drawings can be appointed. At the same time, it is recommended to include no more than three capital letters of the Russian alphabet corresponding to, as a rule, the initial letters of the name of the main set of work drawings. 2 If necessary, the brand of the main sets of work drawings is allowed to be denoted by the letters of the Latin alphabet or digital codes in accordance with the rules established in the standards of organizations. |
||
________________
** The text corresponds to the original. - Note database manufacturer.
Table B.1.
|
Name of the attached document |
|
|
Specification of equipment, products and materials |
|
|
Sketch drawing of the general type of the inepar |
|
|
Construction Product Drawing |
|
|
Poll sheet, overall drawing |
|
|
Local estimates |
|
|
* Calculations, as a rule, are not included in the working documentation, unless otherwise defined in the contract (contract) and the design task. |
|
|
Notes 1 Sifters of other types of attached documents are given in the relevant standards of SPDS or standards of organizations. 2 is allowed, if necessary, ciffers of the attached documents denote the letters of the Latin alphabet in accordance with the rules established in the standards of organizations. |
|
Appendix M (mandatory). Vedomosti shared data on working drawings
Appendix G.
(mandatory)
Form 1 - statement of working drawings of the main kit
Statement of specifications
G.1 In the statement of the working drawings of the main kit indicate:
In the column "Sheet" - the sequence number of the sheet of the main set of work drawings;
In the column "Name" - the name of images placed on a sheet, in accordance with the names given in the main inscription of the sheet;
In the Count "Note" - additional information, for example, changes made in working drawings of the main kit.
G.2 in the statement of specifications indicate:
In the column "Sheet" - the number of the main set of work drawings on which the specification is placed;
In the "Name" column - the name of the specification in exact accordance with its name indicated in the drawing;
In the column "Note" - additional information, including changes made in the specification.
Form 2 - statement of the main sets of work drawings
The statement of reference and accompanying documents
Vedency of documents of the main set of work drawings
G.3 In the statement of the main sets of work drawings indicate:
In the graph "Designation" - the designation of the main set of work drawings and, if necessary, the name or distinctive index of the organization that issued a document;
In the column "Name" - the name of the main set of work drawings;
In the column "Note" - additional information, including changes in the main sets of work drawings.
G.4 The statement of reference and attached documents indicate:
In the graph "Designation" - the designation of the document and, if necessary, the name or distinctive index of the organization that issued the document;
In the "Name" column - the name of the document in exact accordance with the name indicated on the title page or in the main inscription;
In the Count "Note" - additional information, including changes made to the recorded documents included in the working documentation. For documents in electronic form indicate, if necessary, the identifier of the file (files).
G.5 In the statement of documents of the main set of work drawings indicate:
In the graph "Designation" - the designation of the document;
In the column "Name" - the name of the document in accordance with the name specified in the main inscription. For graphic documents consisting of several sheets, the names of images placed on each sheet are also given in accordance with the names given in the main inscription of the sheet;
In the Count "Note" - additional information, including changes made to recorded documents, and, if necessary, the total number of sheets of the document. For documents in electronic form indicate, if necessary, the identifier of the file (files).
G.6 Sizes Count statements, if necessary, can be changed at the discretion of the developer.
G.7 is allowed, if necessary, include additional graphs (columns), for example "count. Sheets", etc.
G.8 When filling out the statements by an automated way, horizontal lines, distinctive lines, allowed not to be carried out. In this case, it is necessary to observe the interval of at least one discharge of the press between the texts of the adjacent lines.
Appendix d (mandatory). List of ESCD standards subject to accountable when performing graphic and text documentation for construction
Appendix D.
(mandatory)
Table D.1
|
Designation and name of the standard |
Conditions for applying Standard |
|
GOST 2.004-88 Unified system of design documentation. General requirements for the implementation of design and technological documents on the printing and graphic devices of the Output |
|
|
GOST 2.051-2006 Unified system of design documentation. Electronic documents. General provisions |
|
|
GOST 2.052-2006 Unified system of design documentation. Electronic model model. General provisions |
|
|
GOST 2.101-68 Unified system of design documentation. Types of products |
|
|
GOST 2.102-68 Unified system of design documentation. Types and completeness of design documents |
Taking into account the provisions of GOST 21.501, relating to the performance of the drawings of construction products |
|
GOST 2.105-95 Unified system of design documentation. General requirements for text documents |
Taking into account the provisions of sections 4, 5 and 8 of this standard |
|
GOST 2.109-73 Unified system of design documentation. Basic requirements for drawings |
|
|
GOST 2.113-75 Unified system of design documentation. Group and Basic Design Documents |
Taking into account the provisions of GOST 21.501 |
|
GOST 2.114-95 Unified system of design documentation. Technical conditions |
Taking into account the provisions 5.2.1, 5.2.2, 5.2.5-5.2.7 and Section 8 of this Standard. Provisions 3.7.1 and 3.8 GOST 2.114 do not take into account |
|
GOST 2.301-68 Unified system of design documentation. Formats |
Taking into account the requirements of the relevant SPDS standards |
|
GOST 2.302-68 Unified system of design documentation. Scale |
Taking into account the provisions 5.1.6 of this Standard |
|
GOST 2.303-68 Unified system of design documentation. Lines |
Taking into account the provisions 5.1.3 of this standard |
|
GOST 2.304-81 Unified system of design documentation. Drawing fonts |
Taking into account the provisions 5.1.5 of this Standard |
|
GOST 2.305-2008 Unified system of design documentation. Images - species, cuts, sections |
Taking into account the provisions of 5.5 of this Standard |
|
GOST 2.306-68 Unified system of design documentation. Designations Graphic materials and rules for their application in drawings |
Taking into account the provisions of GOST 21.302, Tables 4 and 5 |
|
GOST 2.307-2011 Unified system of design documentation. Differences and limit deviations |
Taking into account the provisions 5.4.1-5.4.4 of this Standard |
|
GOST 2.308-2011 Unified system of design documentation. Specifying forms and location of surfaces |
Taking into account the provisions of GOST 21.113 |
|
GOST 2.309-73 Unified system of design documentation. Roughness designation surfaces |
|
|
GOST 2.310-68 Unified system of design documentation. Application in drawings of designations of coatings, thermal and other types of processing |
|
|
GOST 2.311-68 Unified system of design documentation. Image of thread |
|
|
GOST 2.312-72 Unified system of design documentation. Conditional images and designations of welded joints |
|
|
GOST 2.313-82 Unified system of design documentation. Conditional images and notation of all-point connections |
|
|
GOST 2.314-68 Unified system of design documentation. Indications in drawings on marking and branding products |
|
|
GOST 2.315-68 Unified system of design documentation. Images simplified and conditioner fasteners |
|
|
GOST 2.316-2008 Unified system of design documentation. The rules for applying inscriptions, technical requirements and tables on graphic documents. General provisions |
Taking into account the provisions 5.4.5-5.4.7 of this Standard |
|
GOST 2.317-2011 ECCD. Axonometric projections |
|
|
GOST 2.501-88 ECCD. Rules for accounting and storage |
In the form of the inventory book, subscriber card and instructions for folding drawings |
|
GOST 2.511-2011 Unified system of design documentation. Rules for the transfer of electronic design documents. General provisions |
|
|
GOST 2.512-2011 Unified system of design documentation. Rules for performing a data packet for transmitting electronic design documents. General provisions |
|
|
Note - The conditions for the application of ECC standards of the classification group 7 are defined by the SPDS standards, in which links to these standards are given. |
|
Appendix E (recommended). A list of permissible cuts of words used in graphic documents (Supplement to GOST 2.316)
Table E.1.
|
Full name |
Abbreviation |
|
Highway |
|
|
Canceled |
|
|
Antisaismic seam |
|
|
Architect |
|
|
Asphalt concrete |
|
|
Concrete, concrete |
|
|
Ventilation camera |
ventscamera |
|
Capacity |
Navy. (C, T) |
|
Chief Engineer |
GL Ing. (about) |
|
Chief Engineer (Architect) of the Project |
GUI (HAP) (O) |
|
Chief Specialist |
GL specialist. (about) |
|
Expansion joint |
|
|
Director |
|
|
Document |
dock. (T, O) |
|
Permissible |
|
|
Railway |
|
|
Railway |
|
|
Reinforced concrete, reinforced concrete |
|
|
Head |
|
|
Insulation, isolation |
|
|
Institute |
|
|
Design |
|
|
Coefficient |
|
|
Efficiency |
|
|
Staircase, stairs |
|
|
Workshop (in project organizations) |
|
|
Materials |
mat-lies |
|
Mounting |
norm. Narr. |
|
Equipment |
|
|
calculate Narr. |
|
|
Sanitary-technical |
san. tehn |
|
Toilet |
san. knot. |
|
Well |
|
|
Snow |
|
|
Temperature seam |
|
|
Technological |
|
|
Rail head level |
ur. G. R. (and) |
|
The level of soil (underground) water |
|
|
Ground level |
|
|
Pure floor level |
|
|
Foundation |
|
|
Cement, cement |
|
|
Cement concrete |
|
|
Plaster |
|
|
Crushed stone, rubble |
|
|
Electric |
|
|
eL-T (and, T) |
|
|
Notes 1 abbreviations marked with the sign (O) apply only in the main inscription; (T) - in the tables; (C) - with numbers or ciphers; (and) - in graphic images. 2 reductions in the words specified in this table and GOST 2.316 is allowed to be indicated in text documents broken into graphs. |
|
Appendix F (mandatory). Main inscriptions and additional graphs for them
Appendix J.
(mandatory)
Form 3 - for sheets of major sets of work drawings, graphic documents of project documentation and graphic documents on engineering surveys
Note - For graphic documents on engineering surveys, the entry "N. Contiver" ("Normokontrol") in the main inscription is allowed not to perform.
Form 4 - for the drawings of building products (first sheet)
(Amendment. IUS N 1-2015).
Form 5 - for sketchy drawings of general types of non-type products, all types of text documents (first or title sheet)
Note - The main inscription in form 5 is allowed to use for graphic documents on engineering surveys not used in the design as a graphic basis.
Form 6 - for drawings of construction products, sketching drawings of common types of non-type products and all types of text documents (subsequent sheets)
Note - The main inscription in form 6 is allowed to be used for subsequent sheets of graphic documents on engineering surveys not used in design as a graphic basis.
In the graphs of the main inscription and additional graphs to it (the number of the graph is listed in brackets) lead:
In column 1 - the designation of the document, including a text or graphical document of the section, subsection of project documentation, the main kit of working drawings, product drawing, etc.;
In column 2 - the name of the enterprise and, if necessary, its parts (complex), the housing and civil complex or another construction object, which includes a building (structure), or the name of the neighborhood;
In column 3 - the name of the building (structures) and, if necessary, the type of construction (reconstruction, technical re-equipment, overhaul);
In column 4 - the name of images placed on this sheet, according to their name in the drawing. If one image is placed on the sheet, it is allowed to bring it only in column 4.
Names of specifications and other tables, as well as text indications related to images, in column 4 do not indicate (except when specifications or tables are made on separate sheets).
On the sheet (sheets) of general data on working drawings in column 4 record "General data".
In the case provided for in 5.2.3, in column 4 lead the name of the document or the non-type product;
In column 5 - the name of the product and / or the name of the document;
In column 6 - the conditional designation of the type of documentation: P - for project documentation, P - for working documentation.
For other types of documentation, the graphs do not fill or lead symbols established in the standards of the organization;
In column 7 - the sequence number of the sheet of document. On documents consisting of one sheet, the graph is not filled;
In column 8 - the total number of document sheets. The graph is filled only on the first sheet;
In column 9 - the name or distinctive index of the organization that has developed a document;
In column 10 - the nature of the work performed by the person signing the document, in accordance with the forms of 3-5. In free lines, at the discretion of the project organization, specialists and managers responsible for the development and verification of the document are given. In the row under the record "developed" instead of office allowed to bring the record "checked".
Signatures of the person who has developed this document and normocontroller are mandatory.
The lower line provides the position of person who approved the document, such as the chief engineer (architect) of the project, the head of the department or other responsible for this document (sheet) of the official.
Signatures of the person responsible for the preparation of project or working documentation (the chief engineer (architect) of the project) are binding on sheets of general data on working drawings, the most significant sheets of the graphic part of the project documentation and work drawings;
In columns 11-13 - surnames and signatures of the persons specified in column 10 and the date of signing.
Signatures of other officials and matching signatures are placed on the field to cover sheet;
In columns 14-19 - information about the changes that are filled in accordance with 7.3.21;
In column 20 - the original number of the original;
In column 21 - the signature of the person who accepted the script for storage, and the acceptance date;
In column 22 - the inventory number of the original document, in return for which a new script was released;
In column 23 - the designation of the material of the part (the graph is filled only in the drawings of the parts);
In column 24 - a mass of the product shown in the drawing, in kilograms without specifying a unit of mass. The mass of the product in other units of mass leads with an indication of the mass unit.
Example - 2.4 tons;
In column 25 - scale (affilted in accordance with GOST 2.302);
In column 26 - the designation of the format of the sheet according to GOST 2.301. For an electronic document, the sheet format is indicated on which the image will correspond to the set scale;
In column 27 - the brief name of the customer organization.
Notes
1 In columns 13, 19, 21, when specifying the calendar dates on paper, the year indicates the last figures, for example, 02/02/12.
2 Count 27, specified by the stroke line, is administered if necessary.
3 columns "coordinated" (10-13) located on the field for the binder is allowed to bring only those sheets where it is necessary. If necessary, they repeat them.
4 is allowed, if necessary, change the location and dimensions of additional graphs placed on the binder field, in accordance with GOST 2.004.
Appendix and (mandatory). Location of the main inscription, additional graph to it and the size of the frames on the sheets
Appendix I.
(mandatory)
Notes
1 In brackets specified the allowable size of the lower frame.
2 graphs specified by the dash line are introduced if necessary.
Figure and.1 - location of the main inscription, additional graph and frame size
Figure and.2 - The allowable location of the main inscription on the A4 sheet
Appendix K (mandatory). Specifications
Appendix K.
(mandatory)
Form 7 - Specification
Form 8 - Group Specification
Q.1 in specifications indicate:
In the column "Pos." - positions (brands) of structural elements, installations;
In the graph "Designation" - the designation of the main documents on the elements of structures, equipment, products or standards (technical conditions) on them recorded in the specification (technical conditions) on them;
In the column "name" - the name of the elements of structures, equipment, products, materials and their designations (brands), as well as, if necessary, the technical specifications of the equipment and products. It is allowed to the group of the same elements indicate the name once and emphasized it.
The specification records materials directly included in the design, product, and the like in the specified design, product.
In the specification made in electronic form, a horizontal trait included in the designation of materials (rolled, pipes, etc.) is allowed to be replaced by oblique line (/);
In the column "count." Form 7 - the number of items.
In the column "count." Forms 8 - instead of dots write "according to the scheme", "on the floor", etc., and below - the ordinal numbers of the location or floors;
In the column "Mass of units, kg" - a lot of kilograms. It is allowed to give a mass in tons, but indicating a mass unit;
In the graph "Note" - additional information, such as a unit of mass.
K.2 Sizes Count Specifications at the discretion of the developer, if necessary, can be changed.
K.3 when the specifications are filled with an automated way of a line, distinguishing horizontal lines, allowed not to be carried out.
Form 9 - permission to make changes (first sheet)
Form 9A - permission to make changes (subsequent sheets)
L.1 in permission graphs indicate:
The column 1 shows the designation of the permission consisting of the sequence number of permission on the registration book of permissions according to GOST R 21.1003 and through the dividing sign (hyphen, inclined line, etc.) - the last two digits of the year.
Example - 15-12; 15/12;
In column 2 - the designation of the document in which the change makes;
In column 3 - the name of the construction object;
In column 4 - another serial number assigned to changes that contribute to the document in one permission. It is indicated for the entire document, regardless of how many sheets it is completed. The ordinal numbers of the changes are denoted by Arabic figures;
In column 5 - numbers of sheets of a document in which changes make;
In column 6 - the content of the change in the form of a text description and / or graphic image;
In column 7 - the code of the cause of the change in accordance with Table L.1.
Table l.1
It is allowed to change the cause of the change not to indicate. In this case, the graph is fought;
In column 8 - additional information;
In columns of 9-11 - the names of persons signing permission, their signatures and the date of signing;
In column 12 - the name of the project organization and the division (department), which resolved;
In columns 13-16 - the name of the respective divisions or organizations, positions and the names of persons in the prescribed manner agree on permission, their signatures and the date of signing, as well as the signature of the normocontroller;
In column 17 - the sequence number of the resolution sheet. If the resolution consists of one sheet, the graph is not filled;
In column 18 - the total number of resolution sheets.
L.2 is allowed for subsequent sheets permission to use form 9.
Notes
1 is allowed to supplement the form of graphs to identify the resolution in electronic form. Location and dimensions Count Project organization establishes independently.
2 In columns 11, 16, when specifying the calendar date on paper, the year indicates the last two figures.
Form 10 - Change Registration Table (Text document)
|
Table registration table |
||||||||
|
Rooms of sheets (pages) |
Total sheets (pages) in the dock. |
Dock number. |
||||||
|
changed |
replaced |
canceled |
||||||
M.1 Sizes Count table in form 10 Sets the document developer.
M.2 In the graphs of the Change registration table indicate:
In the column "Izm." - the sequence number of document change;
In the graphs "of sheet numbers (pages) of modified, replaced, new, canceled" - numbers of sheets (pages), respectively, modified, replaced, added and canceled for this permission.
When replacing all the sheets of the original (with the next order number of the document change) in the "Replaced" column indicate "All". In the rest of the graphs they put a fiber;
In the column "all sheets (pages) in the dock." - the number of sheets (pages) in the text document after making changes;
In the column "Dock number" - permit designation;
M.3 When replacing all the script sheets, the Changes Registration Table in form 10 do not reproduce the number of changes and other data relating to all the changes previously contributed.
Form 11 - Change Registration Table (Title List and Cover)
M.4 In the graph of the registration table of changes in form 11 indicate:
In the column "Izm." - sequence number of changes in document or volume;
In the column "n dock." - designation of permission to make changes in accordance with the instructions in the application l;
In the column "sub." - signature of the person responsible for the correctness of the change;
In the category "Date" - the date of making a change.
M.5 If necessary, the number of rows can be increased.
M.6 When replacing a document or volume in the registration table in the form 11 form, do not reproduce the number of changes and other data related to all previously added changes.
H.1 on the cover leads the following details:
The name of the construction object on the cover must comply with the information provided in graphs 2 and 3 of the main inscription (see Appendix G);
Field 9 - volume number on the statement "The composition of the project documentation" or "Composition of reporting documentation on the results of engineering surveys" (if available);
Field 10 - year of issue of the document;
Field 11 - To place the registration table of changes in the form 11 of the application M (if necessary).
H.2 The dimensions of the fields 1-11 are set arbitrarily; The lines of the fields specified in the form are not applied; Numbers and names of fields do not indicate.
H.3 is allowed to provide additional details and attributes in accordance with the requirements established in the standards of the organization.
H.4 Cover sizes are taken depending on the volume format, folder or album, to which it is performed.
P.1 On the title page, the following details lead:
Field 1 - abbreviated, and in its absence - the full name of a higher organization (if available); indicate, as a rule, for state organizations;
Field 2 - logo (optional), the full name of the organization prepared by the document;
Field 3 - number and date of issuance of a certificate of admission to the relevant types of work (on the preparation of project documentation or surveys), which influence the safety of the object of capital construction;
Field 4 - a brief name of the customer organization (if necessary). The name indicates: "Customer - the name of the organization-customer";
Field 5 - the name of the object of capital construction and, if necessary, the type of construction.
The name of the construction object on the title page must comply with the information provided in graphs 2 and 3 of the main inscription (see Appendix G);
Field 6 - type of documentation (if necessary);
Field 7 - document name;
Field 8 - document designation;
Field 9 - volume number on the statement "Composition of project documentation" or "Composition of reporting documentation for engineering research" (if available);
Field 10 - posts responsible for the development of the document;
Field 11 - signatures of persons indicated on the field 10, performed according to GOST R 6.30. This field also includes the registering of the organization that prepared the document;
Field 12 - initials and surnames of the persons specified on the field 10;
Field 13 - year of issue of the document;
Field 14 - to place the registration table of changes in the form 11 of the application M (if necessary);
Field 15 - for additional graph of the main inscription in accordance with the application of J. The information contained in these graphs is allowed to bring in another form in accordance with the requirements established in the standards of the organization.
P.2 The size of fields 1-14 is set arbitrarily; The lines of these fields specified in the form are not applied, the numbers and names of the fields do not indicate.
C.3 is allowed to make a title page without frames.
P.4 is allowed to bring additional details and attributes in the title page in accordance with the requirements established in the standards of the organization.
P.5 The dimensions of the title leaf are taken depending on the volume format, the folder or album to which it is performed.
Appendix P (Reference). Examples of the performance of title sheets
Appendix R.
(Reference)
_______________
* The examples are conditional.
Figure P.1 - Example of the title Tom of Project Documentation
Figure P.2 - Example of the title sheet of volume (folders) of working documentation
Appendix C (recommended). The composition of the project documentation. The composition of the reporting documentation on the results of engineering surveys
C.1 in Vedomosti indicate:
In the column "Tom number" - the sequence number of the volume volume or volume number, which includes the section number and, if available, the number of subsection, parts, books (see 4.1.1, 4.1.3), separated by points.
Example - 1, 2.1, 2.2, 5.5.1, 5.5.2;
In the graph "Designation" - the designation of the document (volume) indicated on its title page, and, if necessary, the name or distinctive index of the organization that issued a document;
In the "Name" column - the name of the document (volume) in exact accordance with the name indicated on its title sheet;
In the column "Note" - additional information, including changes made.
C.2 Sizes Count Vedomost at the discretion of the developer, if necessary, can be changed.
C.3 When filling out the statement by an automated way, horizontal lines, distinctive lines, allowed not to be carried out.
Federal Agency
On technical regulation and metrology
Preface
1 Developed by an open joint-stock company "Center for the Methodology of Regulation and Standardization in Construction" (OJSC "CNS")
2 Submitted by the Technical Committee on Standardization TC 465 "Construction"
3 APPROVED AND INTRODUCED BY Order of the Federal Agency for Technical Regulation and Metrology of June 11, 2013 No. 156-st
4 In this standard, the norms of the Urban Planning Code of the Russian Federation of December 29, 2004 No. 190-FZ were implemented.
5 instead of GOST R 21.1101-2009
The rules for applying this standard are set to GOST R 1.0-2012 (Section 8). Information about the changes to this standard is published in the annual (as of January 1 of the current year) the information indicator "National Standards", and the official text of the amendments and amendments in monthly information indicator "National Standards". In case of revision (replacement) or the cancellation of this standard, the appropriate notification will be published in the nearest issue of the monthly information indicator "National Standards". Relevant information, notice and texts are also posted in the public information system - on the official website of the Federal Agency for Technical Regulation and Metrology on the Internet (GOST.RU)
| 1 area of \u200b\u200buse. 3. 3 Terms, definitions and reductions. five 3.1 Terms and definitions. five 3.2 Reduction. 7. 4 General requirements for the composition and recruitment of project and working documentation. 7. 4.1 Project documentation. 7. 4.2 Working documentation. nine 4.3 General data on working drawings .. 11 5 General Rules for the implementation of documentation. 12 5.1 General. 12 5.2 Main inscriptions. 13 5.3 Coordination axes. fourteen 5.4 Drawing sizes, slopes, marks and inscriptions. sixteen 5.5 Images (cuts, sections, species, remote elements) 19 6 rules for performing specifications in the drawings. 22. 7 Rules for making changes. 22. 7.1 General. 22. 7.2 Permission to make changes. 23. 7.3 Amendments. 23. 7.4 Features of making changes to project documentation .. 28 7.5 Features of making changes to working documentation .. 29 8 Rules for registration of discharged documentation. thirty Appendix M (compulsory) Vedency of general data on working drawings .. 35 Appendix D (compulsory) List of ECCD standards subject to accountable in the implementation of graphic and text documentation for construction. 36. Appendix F (Mandatory) Main inscriptions and additional graphs for them .. 38 Appendix and (mandatory) Location of the main inscription, additional graph to it and the size of the frames on sheets. 42. Appendix K (mandatory) specification. 43. Appendix P (Reference) Examples of the performance of title sheets. 52. Bibliography. 55. |
National Standard of the Russian Federation
System of design documents for construction
Basic requirements for project and working documentation
System of Design Documents for Construction.
Main Requirements for Design and Working Documents
Date of administration- 2014-01-01
1 area of \u200b\u200buse
This standard establishes the basic requirements for project and working documentation for the construction of various appointments.
Note - In this standard, the concept of "construction" includes new construction, reconstruction, technical re-equipment and overhaul of capital construction facilities.
The general rules for the implementation and recruitment of graphic and text documentation established in 4.1 and in sections 5 and 8, and the rules for making changes established in Section 7 are also applied to the reporting technical documentation on the results of engineering surveys for construction.
This standard uses regulatory references to the following standards:
GOST R 6.30-2003 Unified documentation systems. Unified system of organizational and administrative documentation. Document Requirements
GOST R 21.1001-2009 Project documentation system for construction. General provisions
GOST R 21.1002-2008 Project documentation system for construction. Normocontrol project and working documentation
GOST R 21.1003-2009 Project documentation system for construction. Accounting and storage of project documentation
GOST R 21.1703-2000 System of project documentation for construction. Rules for performing working documentation of wired communication
GOST 2.106-96 Unified system of design documentation. Text documents
GOST 2.308-2011 Unified system of design documentation. Instructions forms and location of surfaces
GOST 2.309-73 Unified system of design documentation. Roughness designation surfaces
GOST 2.314-68 Unified system of design documentation. Instructions in the drawings on the labeling and branding of products
GOST 2.317-2011 Unified system of design documentation. Axonometric projections
GOST 2.501-88 Unified system of design documentation. Rules for accounting and storage
GOST 21.110-95 The system of project documentation for construction. Rules for the implementation of the Specification of Equipment, Products and Materials
GOST 21.113-88 System of project documentation for construction. Characteristics of accuracy
GOST 21.114-95 Project documentation system for construction. Rules for performing draft drawings of common types of non-type products
GOST 21.302-96 Project documentation system for construction. Conditional graphics symbols in engineering and geological research documentation
GOST 21.408-93 System of project documentation for construction. Rules for performing working documentation of automation of technological processes
GOST 21.501-2011 System of project documentation for construction. Rules for the fulfillment of working documentation of architectural and constructive solutions
GOST 21.709-2011 System of project documentation for construction. Rules for the fulfillment of working documentation of linear structures of hydromelic systems
Note - When using this standard, it is advisable to check the action of reference standards in the public information system - on the official website of the Federal Agency for Technical Regulation and Metrology on the Internet or on the National Standards Annual Information Signal, which is published as of January 1 of the current year, and on the issues of the monthly information pointer "National Standards" for the current year. If the reference standard is replaced, to which the undated link is given, it is recommended to use the current version of this standard, taking into account all changes made to this version. If the reference standard is replaced by a dated reference, it is recommended to use the version of this standard with the above-mentioned approval (adoption). If, after approval of this standard in the reference standard, to which the dated reference is given, the change has been made affecting the provider to which the link is given, this provision is recommended to be applied without taking into account this change. If the reference standard is canceled without replacement, the position in which the reference is given to it is recommended to be applied in a portion that does not affect this link.
3 Terms, Definitions and Reducing
3.1 Terms and Definitions
In this standard, the terms of software are applied, GOST R 21.1001, GOST R 21.1002, GOST R 21.1003, as well as the following terms with the corresponding definitions:
3.1.1 main inscription:A combination of information about the project document contained in the columns of the table of the installed form placed on sheets of project and working documentation.
3.1.2 the main set of work drawings:A graphical document containing the necessary and sufficient information in the form of drawings and schemes intended for the production of construction and installation works of a certain type (mark).
3.1.3 full set of working documentation:The combination of the main sets of the work drawings necessary for the construction of a building or structure, complemented by the attached and reference documents.
3.1.4 brand:The letter or alphanumeric index entering the designation of working documentation and determining its attitude to a certain type of construction and installation work, or denoting the main distinguishing features of building structures and their elements.
specification of equipment, products and materials:A text project document that determines the composition of equipment, products and materials intended for the acquisition, preparation and implementation of construction.
[GOST 21.110-95, SECTION 3]
sketch drawing of the general type of the inepar product:A document determining the initial design of the non-type product containing a simplified image, the main parameters and technical requirements for the product in the amount of source data (tasks) required to develop design documentation.
[GOST 21.114-95, Article 3.1]
3.1.7 nepical product:The product (design, device, mounting unit) of technological systems, internal and external systems and networks of engineering and technical support of buildings and structures, first developed and manufactured, as a rule, on the installation site (in the procurement workshop of the assembly organization).
building structure:Part of the building or structure performing certain carriers, enclosing and (or) aesthetic functions.
[GOST 21.501-2011, Article 3.3]
construction element:Compound part of the national team or monolithic design.
[GOST 21.501-2011, Article 3.5]
3.1.12 equipment:Technological equipment (machines, apparatus, mechanisms, lifting and other technical means providing the appropriate technological process), as well as engineering equipment of buildings and structures, ensuring safe and favorable conditions for people's vital activity.
coordination axis:One of the coordination lines that determine the membership of the building or facing the modular steps and the height of the floors.
[GOST 28984-2011, Article 3.12]
3.1.14 plan:Top view or horizontal section of a building or structure.
3.1.15 facade:Orthogonal projection of the outer wall of the building or facilities on the vertical plane.
Note - the facades of the main, side, yard, etc. differ.
document props:The design element of the document containing information about it.
Note - As a rule, props consists of attributes (composite props).
[GOST 2.104-2006, Article 3.1.1]
document attribute:Identified (named) characteristic of part of the props.
[GOST 2.104-2006, Article 3.1.2]
signature:The details of the document, which is a personal signature of the authorized official.
Note - For electronic documents, an analogue of its own signature is used - an electronic digital signature.
[GOST 2.104-2006, Article 3.1.4]
3.1.20 Designation:Props of the document, which is its identification (distinctive) index.
Note - Each document is assigned the designation that is recorded in the established locations (in the main inscriptions, on title sheets, etc.).
3.2 Abbreviations
This standard uses the following abbreviations:
DE - electronic document;
ECCD - a unified system of design documentation;
CAD - automated design system (systems);
SPDS - a system of project documentation for construction;
SED - system (system) of electronic document management.
4 General requirements for the composition and acquisition of project and working documentation
4.1 Project documentation
4.1.1 The composition of the project documentation of capital construction facilities and the requirements for its content are established by the legislation approved by the Government of the Russian Federation by the provision and regulatory acts of federal executive bodies.
Project documentation is equipped, as a rule, according to individual sections and subsections established by the Regulation. The names and ciphers of the project documentation sections are given in Tables A.1 and A.2 (Appendix A).
In paper form, project documentation is equipped in volumes in accordance with 4.1.4, 4.1.5 and section 8.
With a large volume (in paper form) of the partition or subsection, as well as, if necessary, in other cases (for example, when attracting subcontractors), it is allowed to divide it into parts, and parts, if necessary, on books. Each part and book are completed separately. All parts and books give names reflecting the content of parts or books. Subsections, parts and books are assigned by the sequence numbers of Arabic numbers within, respectively, the partition, subsection or part.
4.1.2 Each partition, subsection, parts and, if necessary, the book complied with, as well as each text and graphical document included in the Self-denotation, which indicates the cover, the title page and / or in the main inscription, as well as in footer columns of text documents performed without major inscriptions.
4.1.3 The designation of the section includes a basic designation set by the system in effect in the project organization, and through a hyphen * - code documentation section. The basic designation includes, for example, a contract number (contract) and / or construction object code (digital, alphabetic or alphanumeric). The basic designation is allowed to include other codes used in CAD and EDS.
* In the designation, other separation signs are allowed, such as a point, inclined line, etc.
If the partition is divided into parts, the part designation is made up of the designation of the partition to which the part number is added.
Examples
1 2345-PZ- Section 1. Explanatory note.
2 2345-ROM1- Section 2. Scheme of the planning organization of the land plot. Part 1. General.
3 2345-ROM2- Section 2. Scheme of the planning organization of the land plot. Part 2. Solutions for internal rail transport.
If the part is divided into books, the designation of the book is from the designation of the part to which the book number is added through the point.
The designation of the subsection is made up of the designation of the section to which the subsection number is added.
If the subsection is divided into parts, the designation of the part is made up of the designation of the subsection to which the part number is added via the point. If the part is divided into books, the designation of the book (if necessary) is made up of the part of the part to which the book number is added through the point.
Examples
1 2345-IOS4.1.1- Section 5. Information about engineering equipment, engineering and technical support networks, a list of engineering and technical measures, the content of technological solutions. Subsection 4. Heating, ventilation and air conditioning, thermal networks. Part 1. Heating, ventilation and air conditioning. Book 1. Basic solutions.
2 2345-IOS4.1.2- Section 5. Information about engineering equipment, engineering and technical support networks, a list of engineering and technical measures, the content of technological solutions. Subsection 4. Heating, ventilation and air conditioning, thermal networks. Part 1. Heating, ventilation and air conditioning. Book 2. Systems of automation of heating, ventilation and air conditioning.
3 2345-IOS4.2- Section 5. Information about engineering equipment, engineering and technical support networks, a list of engineering and technical measures, the content of technological solutions. Subsection 4. Heating, ventilation and air conditioning, thermal networks. Part 2. Thermal networks.
Based on the provisions 4.1.1 - 4.1.3, 4.2.3 - 4.2.7, standards of organizations may be developed to designate textual and graphic documents that are part of the design and working documentation that take into account the characteristics of the designation depending on the amount of documentation, document management conditions and used CAD and SED.
4.1.4 Text and graphic materials included in the general case are completed in the following order:
Cover;
Title page;
The statement "The composition of the project documentation".
Note - It is allowed not to include the statement of the "composition of the project documentation" in each volume, but to equip it with a separate volume;
Text part;
Graphic part (drawings and schemes).
The rules for designing the cover, the title list, the content of volume and the statement "The composition of the project documentation" are given in section 8.
4.1.5 The number of sheets included in that is determined from the need to ensure the convenience of work, as a rule, not more than 300 sheets of A4 format according to GOST 2.301 or the equivalent number of sheets of other formats.
4.1.6 General requirements for the execution of graphic documentation are given in section 5.
4.1.7 Text documents containing mainly solid text (including text part parts and project documentation subsections) are performed according to GOST 2.105, taking into account 5.1, 5.2 of this standard.
4.1.8 It is allowed to perform the text documents specified in 4.1.7, without major inscriptions, additional graph to them and the framework. In this case:
On the first sheet, lead a list of performers, which indicates positions, initials and surnames of persons who participated in the development, control and coordination of a text document, and provide places for signatures and dates of signing. On the second and, if necessary, the subsequent sheets place the content (table of contents), which includes numbers (designations) and the names of sections, subsections and text document applications indicating sheet numbers (pages);
At the top of the (top footer) of each sheet indicate the designation of the document: in the left corner (with one-sided print) or the right corner of the even pages and the left corner of odd pages (with double-sided printing);
At the bottom of the (lower footer) of each sheet indicate: the logo and name of the organization that prepared the document, the name of the document, the number of the sheet (pages) of the document (in the lower right corner - with one-sided seal or in the left corner of the even pages and the right corner of odd pages - Two-way printing), as well as, if necessary, the version number of the document, the identifier (name) of the file and other information. The logo is allowed and the name of the organization to bring in the top footer;
Change data indicate in accordance with 7.3.
4.1.9 Calculations of constructive and technological solutions, which are a mandatory element of the preparation of project documentation, are not included in the design documentation. They are issued in accordance with the requirements for text documents and are stored in the archive of the project organization. Calculations submit to the Customer or Expertise Authorities on their requirement.
4.2 Working documentation
4.2.1 The working documentation transmitted to the Customer includes:
Workers drawings combined into the main sets of work drawings on stamps. The brands of the main sets of work drawings are shown in Table B.1 (Appendix B);
The accompanying documents developed in addition to the working drawings of the main kit.
4.2.2 The main sets of work drawings include general data on working drawings, drawings and schemes provided for by the relevant SPDS standards.
4.2.3 The main set of work drawings of any brand can be divided into several basic sets of the same brand (with the addition of the sequence number) in accordance with the process of organizing construction and installation work.
Example - AR1; AR2; Kzh1; Kzh2.
4.2.4 Each basic set of work drawings is assigned the designation, which includes the basic designation, installed on the system being operating in the organization, and through the hyphen - the brand of the main kit.
Example - 2345-12-AR,
where 2345-12 is the basic designation. The basic designation includes, for example, the contract number (contract) and / or the construction object code (see 4.1.3), as well as the building number or structure by the master plan *;
* For working drawings of linear structures, master plan, outdoor communications, this part of the base designation is excluded or replaced by zeros.
Ar is the brand of the main set of work drawings.
4.2.5 It is allowed to form a basic set of work drawings with individual documents with the assignment of the designation consisting of the basic designation, the brand of the main kit, and by adding the Arabic figures through the point number.
Example - 2345-12-E0.1; 2345-12-E0.2,
where 2345-12 is the basic designation;
EO - brand of the main set of work drawings;
1, 2 - sequence numbers of documents of the main set of work drawings.
The first document with such registration of the main set of work drawings should be general data on working drawings.
4.2.6 The attached documents include:
Working documentation for construction products;
Sketch drawings of common types of non-type products performed in accordance with GOST 21.114;
Specification of equipment, products and materials performed in accordance with GOST 21.110;
Polls and overall drawings performed in accordance with the manufacturers (suppliers) of equipment;
Local estimate;
Other documents stipulated by the relevant SPDS standards.
The specific composition of the accompanying documents and the need for their implementation are set by the relevant SPDS standards and the design task.
The accompanying documents design organization conveys the Customer simultaneously with the main set of work drawings in the amount established for the work drawings.
4.2.7 Each accompanying document assign the designation of the main kit with the addition of an enclosed document through the cipher. Encipers of the attached documents are shown in Table B.1 (Appendix B).
Example - 2345-12-EO,
where 2345-12-EO is the designation of the main set of work drawings;
C - cipher specification of equipment, products and materials.
If there are several attached documents of one species to their designation, a sequence number or, through a hyphen, a product brand (for product drawings) is added.
Example - 2345-12-VK.N1; 2345-12-VK.N2, 2345-12-KZH.I-B1, 2345-12-KZH.I-B2
4.2.8 In the working drawings, it is allowed to use typical building structures, products and nodes by references to documents containing workers drawings of these structures and products. Reference documents include:
Standards that include drawings intended for the manufacture of products;
Drawings of typical designs, products and nodes **.
** If necessary, drawings of typical designs, products and nodes are recorded in the "Accellenged Documents" section (as a rule, without changing the designation) and transferred to the Customer in accordance with 4.2.6.
Reference documents are not included in the working documentation transmitted to the customer. The project organization, if necessary, transmits them to the customer under a separate agreement.
4.2.9 Form, rules for the implementation and designation of the document, which provides the composition of all working documentation made in accordance with the Treaty, are established in the standards of the organization.
4.3 General data on working drawings
4.3.1 In the first sheets of each main set of work drawings, general data on working drawings are included in which include:
The statement of working drawings of the main kit performed in form 1;
The statement of reference and accompanying documents performed in form 2;
The statement of the main sets of work drawings performed in form 2;
The statement of specifications (if there is mainly a set of several location schemes), performed in form 1;
The symbols not established by national standards and the values \u200b\u200bof which are not indicated on other sheets of the main set of work drawings;
General instructions;
Other data provided for by the relevant SPDS standards. Forms 1 and 2 with instructions for completing them are given in Appendix G.
4.3.2 The statement of working drawings of the main kit contains a sequential list of sheets of the main kit.
When designing a basic set of work drawings with separate documents (see 4.2.5) instead of the statement of the working drawings of the main kit, includes the statement of the documents of the main kit in form 2, and in each of the subsequent documents of the main kit leads links to general data on working drawings .
4.3.3 The report of reference and the accompanying documents are partitions:
Reference documents;
Attached documents.
The "Reference Documents" section indicates documents according to 4.2.8. At the same time, in the respective graphs, the statements indicate the designation and name of the series and the release number of the drawings of typical structures, products and nodes or the designation and name of the standard.
The "Acceived Documents" section indicates documents according to 4.2.6.
4.3.4 The statement of the main sets of work drawings leads on sheets of general data of one of the main sets of work drawings of the building or structure (at the discretion of the person responsible for developing working documentation). The statement contains a consistent list of the main sets of work drawings, which are part of the full set of working documentation for the building or construction.
If there are several main kits of the working drawings of the same brand (see 4.2.3), they constitute the statement of sets of this brand in form 2 (Appendix D), which is usually given in the general data of each of these sets.
4.3.5 In general directions, lead:
Information about the documents on the basis of which a decision was made on the development of working documentation (for example, a task for designing, approved project documentation);
Recording on the conformity of working documentation The task of design issued by the technical conditions, the requirements of current technical regulations, standards, arrangements of rules, other documents containing established requirements;
A list of technical regulations and regulatory documents containing requirements for technical solutions and further work of work, references to which are given in working drawings;
The absolute mark, accepted in the working drawings of the building or construction conditionally for zero (as a rule, leads to the drawings of architectural and design solutions);
Recording on the results of a patentability and patent purity for the first time used in the project documentation of technological processes, equipment, structures, products and materials, as well as patent numbers and applications for which decisions are made on issuing patents to the inventions used in the working documentation (if necessary);
The list of types of work that affect the safety of the building or structure and for which it is necessary to compile acts of examination of hidden work, responsible structures and sections of engineering and technical support networks;
Information about who owns this intellectual property (if necessary);
Operational requirements for a designed building or building (if necessary);
Other necessary instructions.
In general guidelines, it should not be repeated technical requirements placed on other sheets of the main set of work drawings, and give a description of the technical solutions adopted in the working drawings.
Points of general instructions must have through numbers. Each point of general instructions are recorded from a new line.
5 General Rules for the implementation of documentation
5.1 General
5.1.1 When performing project and working documentation, as well as reporting technical documentation for engineering surveys for construction should be guided by the provisions of the SPDS and ECC standards.
The list of ECC standards subject to accountable in the implementation of graphic and text documentation for construction is given in Table D.1 (Appendix D).
5.1.2 Documentation is typically carried out by an automated manner on paper (in paper form) and / or in the form of DE.
Documents of one type and name, regardless of the method of execution, are equal and interchangeable. Mutual compliance between documents in electronic and paper forms provides a developer.
General requirements for electronic documents - according to GOST 2.051.
5.1.3 In the graphic documents of the image and the symbols are performed by lines according to GOST 2.303. It is allowed to use lines of other types, names, drawing, thickness and main purpose of which are installed in the relevant SPDS standards.
5.1.4 In graphic documents, the conditional designations should be carried out in the main black color. Some conditional designations or their individual elements are allowed to be performed by other colors. Instructions on the color of the symbols are given in the relevant SPDS standards. If the color of the symbols used in the drawings and diagrams are not installed in the standards, their purpose indicates the drawings.
In the scripts intended for the manufacture of black and white copies, colored conditional notation and their elements should be performed in black.
5.1.5 When performing graphic documents, fonts according to GOST 2.304 are used, as well as other fonts used by the means of computing technology, while providing the availability of these fonts to users of documents.
5.1.6 The drawings are performed at an optimal scale according to GOST 2.302, taking into account their complexity and saturation of information.
The scales of images do not indicate the drawings, with the exception of drawings of products and other cases provided for in the relevant SPDS standards. In these cases, the scale is indicated in parentheses immediately after image names in accordance with GOST 2.316 (clause 4.19).
5.1.7 Drawings on paper and electronic drawings (2D) can be performed on the basis of an electronic model (3D) building or structures (GOST 2.052).
5.1.9 The structure and composition of DE details should provide its appeal within software (display, making changes, printing, accounting and storage in databases, as well as transmitting to other automated systems) in addition to regulatory requirements for paperwork.
5.1.10 For consideration, coordination, expertise and approval are copies of documents of project and working documentation, compiled, as indicated in 4.1 and 4.2.
5.1.11 The form of presentation of documents of project and working documentation (paper or electronic), if it is not specified in the design task, is determined by the developer in coordination with the customer. It is allowed to include in the design and working documentation documents in various forms of submission.
5.1.12 The rules for the transfer of documentation on electronic media, including the nomenclature and forms of the necessary accounting and reporting documents, establish in the standards of the organization developed on the basis of GOST 2.051, GOST 2.511 and GOST 2.512.
5.1.13 The list of cuts of words allowed in graphical documents is compiled in addition to GOST 2.316 and is shown in Table E.1 (Appendix E).
5.2 Main inscriptions
5.2.1 Each sheet of graphic and text document, as a rule, is drawn up the main inscription and additional graphs to it. Forms of the main inscriptions and instructions on their completion are given in Appendix J.
Note - The main inscriptions do not make up text documents performed in accordance with 4.1.8, estimates, etc.
The main inscription is placed in the lower right corner of the sheet.
On A4 sheets according to GOST 2.301, the main inscription is placed along the short side of the sheet. For text documents in tabular form is allowed, if necessary, have the main inscription along the long side of the sheet.
On sheets of basic sets of work drawings and sheets of the graphic part of the project documentation - form 3;
On the first sheet of drawings of construction products - form 4;
In the first or title * sheets of text documents and the first sheets of sketch drawings of common types of non-type products, designed in the form of release, - form 5;
* For text documents performed with the title list and the main inscriptions are made, the top is the next sheet after the title leaf.
On the subsequent sheets of drawings of construction products, text documents and sketch drawings of general species - form 6.
The first sheet of the drawing of the construction product is allowed to design the main inscription in form 5.
5.2.3. If some text documents (for example, the specification of equipment, products and materials) are produced without a title list, then in this case the first sheet of the document is issued by the main inscription in form 3, subsequent - in form 6.
When placing the main set of work drawings with separate documents, documents containing solid text and / or in the form of tables (for example, general data, cable journal, etc.) are issued as text documents. In this case, the first sheet of the document is drawn up by the main inscription in form 3, subsequent - in form 6.
5.2.4 In the reporting technical documentation on the results of engineering surveys, the main inscription is used:
On sheets of graphic documents used in the design as a basis - in form 3;
In the first sheets of other graphic and text documents - in form 5, on subsequent sheets - in form 6.
5.2.5 The main inscription, additional graphs for it and the framework are performed by solid thick basic and solid thin lines according to GOST 2.303.
5.2.6 Table of changes in the main inscription (column 14 - 19), if necessary, allowed to continue up or left from the main inscription. When the table of changes to the left of the main inscription name of the name Count 14 - 19 is repeated.
5.2.7 Location of the main inscription and additional graph to it, as well as the size of the frames on the sheets are shown in Figures and.1 and and.2 (Appendix and).
5.2.8 Location and dimensions of additional graph for identification of DE Project organization establishes independently.
5.2.9 It is allowed to additionally identify project documents using bar code.
At the same time, the document designation, version number and the designation of the document should be used as a barcode details. Additionally, the country code, the code of the developer and other details can be used.
5.3 Coordination axes
5.3.1 On the images of the building or structure, the coordination axes of its supporting structures are indicated, intended to determine the mutual arrangement of elements of the building or building and binding a building or structure to a construction geodetic grid or a center base.
5.3.2 Each individual building or construction is assigned an independent system for the coordination axes.
Coordination axes are applied to the images of the building, facilities with thin barccotted lines with long strokes, denoted in the circles with a diameter of 6 - 12 mm Arabic numbers and the capital letters of the Russian alphabet (with the exception of letters: E, 3, th, o, x, c, h, u , Ъ, s, b) or, if necessary, letters of the Latin alphabet (with the exception of letters I and O).
Skipping in digital and letter (except indicated) designations of coordination axes are not allowed.
The figures indicate the coordination axes on the side of the building and facilities with a large number of axes. If there is not enough alphabet letters to designate the coordination axes, the subsequent axes are denoted by two letters.
Example - AA, BB, BB.
5.3.3 The sequence of the coordination axes are taken according to the plan, as shown in Figure 1a: Digital axes - from left to right, alphabetic axes - from the bottom up or as shown in Figures 1 b. and 1 in.
5.3.4 The designation of the coordination axes is usually applied to the left and lower parties of the plan of the building and facilities.
If the coordination axes of the opposite sides are incomprehensible, the plan in the locations of discrepancies additionally apply the designations of the specified axes over the top and / or right parties.
5.3.5 For individual elements located between the coordination axes of the main supporting structures, additional axes are applied to which the designation is assigned in the form of a fraction, in the numerator of which indicate the designation of the preceding coordination axis, and in the denominator - an additional sequence number within the section between the adjacent coordination axes in according to Figure 1 g..
It is allowed by the coordination axes of the half-timbered columns to assign digital and alphabetic designations to the continuation of the designations of the axes of the main columns without an additional number.
5.3.6 In the image of a repeated element affected by several coordination axes, coordination axes are denoted in accordance with the picture:
2a - with their number of no more than 3;
2b. - with their number of more than 3;
2in - With all alphabetic and digital coordination axes.
If necessary, the orientation of the coordination axis, to which the element is tied to the adjacent axis is indicated in accordance with Figure 2 g.
Picture 1
Figure 2.
5.3.7 On the plans of residential buildings arranged from block sections, the extreme coordination axes of the block sections are assigned notation according to 5.3.1 - 5.3.3, which indicate in accordance with Figure 3a.
The coordination axes of block-sections, including extreme, assign independent notation according to 5.3.1 - 5.3.3 with the addition of the index "C" (see Figure 3 b.). If necessary, on the plan of the block section indicate the designations of the coordination axes of the building composed from the block sections.
Figure 3.
5.3.8 Three-dimensional (3D) electronic model of a building or facilities are performed in a single planning and high-rise coordinate system.
The coordinate system of the three-dimensional model of the building or structures is depicted in three mutually perpendicular lines with the beginning of the coordinates located at the point of intersection of axes 1 and and on the zero mark of this building or structure in accordance with Figure 4.
Figure 4.
At the same time, for a rectangular building (see Figure 1a) for a positive direction: axis X.- in the direction of increasing the digital designations of the coordination axes, the axis Y.- in the direction of increasing the letter designations of the coordination axes, the axis Z. - vertically up from the conditional zero level of the building.
5.4 Drawing, slopes, marks and inscriptions
5.4.1 Linear dimensions in drawings indicate without the designation of length units:
In meters up to two places after the communion - in the drawings of external networks and communications, master plan and transport, except in cases specified in the relevant SPDS standards;
In millimeters - on all other types of drawings.
5.4.2 Dimensional line at its intersection with remote lines, contour lines or axial lines are limited by serifs of 2-4 mm long, applied with a slope to the right at an angle of 45 ° to the dimensional line, while the dimensional lines continue for extreme remote lines (or respectively Contour or axis) by 0 - 3 mm.
When applying the size of the diameter or radius inside the circle, as well as the angular size of the dimension line is limited by arrows. Arrows are also used when applying the sizes of radii and internal rounds.
When drawing dimensions on axonometric schemes of technological pipelines and engineering systems, dimensional lines are allowed to be limited by arrows.
5.4.3 levels of levels (heights, depths) of structural elements, equipment, pipelines, air ducts, etc. From the reference level (conditional "zero" mark) indicate in meters without the designation unit with three decimal signs separated from an integer comma, for The exception of the cases specified in the relevant SPDS standards.
Levels of levels on the facades, cuts and sections are placed on remote lines (or on the loop lines) and denote the "¯" sign, performed by solid thin lines with a length of the strokes 2 - 4 mm at an angle of 45 ° to a remote line or contour line, according to Figure 5; On plans - in a rectangle in accordance with Figure 6, with the exception of cases specified in the relevant SPDS standards.
| Figure 5. | Figure 6. |
"Zero" mark taken, as a rule, for the surface of a building of a building or structure, located near the planning surface of the Earth, indicate without a sign; The relative marks above zero indicate the "+" sign, below zero - with the sign "-".
Note - As a zero mark for buildings, as a rule, the level of pure floor of the first floor is taken.
5.4.4 On the plans, the direction of the decontamination of the planes indicates the arrow over which, if necessary, affix the numeric value of the slope in percent in accordance with Figure 7A or in the form of a relationship of the altitude of the plane to the corresponding horizontal projection (for example, 1: 7).
The numeric value of the slope is allowed in the ppm or in the form of a decimal fraction with an accuracy of the third mark.
At cuts, sections and schemes before the dimensional number determining the numerical value of the slope, the sign "ð" is applied, the sharp angle of which should be directed towards the slope (except for the steepness of the slopes and recesses). The designation of the slope is applied directly above the line of the circuit or on the shelf of the lines of the tuning in accordance with Figure 7 .
Figure 7.
5.4.5 Rooms of positions or stamps of elements are applied on the shelves of lines-carrying, conducted from images of elements of structures of buildings or structures, next to the image - without a lifting line or within the contours of the pictures of the elements in accordance with Figure 8.
Figure 8.
Truck line, as a rule, finish with a point. If the lifting line is assigned to the line indicating the surface, then it is completed with the arrow. With a small-scale image, the lifting line finish without arrow and point.
5.4.6 Remote inscriptions to multilayer structures are performed in accordance with Figure 9.
Note - figures are conditionally indicated by the sequence of layers of structures and inscriptions on the shelves of lines.
Figure 9.
5.4.7 The font size for referring to the coordination axes, positions (grades), names and image designations must be 1.5 - 2 times the size of the number of dimensional numbers used in the same graphical document.
5.5 Images (cuts, sections, species, remote elements)
5.5.1 Images in the drawings are performed in accordance with GOST 2.305, taking into account the requirements of this standard and other SPDS standards.
5.5.2 Sections of buildings or structures are denoted by Arabic numbers sequentially within the graphical document. Sections are denoted in the same way.
NOTE - In the drawings of the design and working documentation, the incision is called, as a rule, a vertical section of a building or structure, that is, a cut, made by a secular plane perpendicular to the horizontal plane of projections.
Self-numbering is allowed for cuts and sections of individual sections of the building, structures or installations, all the drawings of which are located on one sheet or sheets of sheets and if there are no references to cuts and sections on these drawings located on other sheets of graphics document.
It is allowed to designate cuts by the capital letters of the Russian alphabet, and the sections - the capital or lower case letters of the Russian alphabet (with the exception of the letters specified in 5.3.2).
The position of the secular plane indicates the drawing of the cross section line (open line 2.303 linte). With a complex section, the strokes are also carried out in the intersection of the sequential planes among themselves. On the initial and finite strokes should be put the arrows indicating the direction of the view; Arrows should be applied at a distance of 2 - 3 mm from the end of the stroke (Figure 10).
The direction of the view for a cut according to the plan of the building and facilities takes, as a rule, from the bottom up and right to left.
5.5.3 If separate parts of the form (facade), the plan, the cut require a more detailed image, then further perform local species and remote elements - nodes and fragments.
5.5.4 In the image (plan, facade or section), from where the node is removing, the corresponding place is noted by a closed solid thin line (circumference, an oval or a rectangle with rounded corners) with application on the shelf of the lines of the notation of the Arabic node of the Arabic node in accordance with Figures 11a , eleven b. or the capital letter of the Russian alphabet in accordance with Figure 11 in.
If you need to link to the node placed in another graphic document (for example, the main set of work drawings), or on the working drawings of the typical construction site indicate the designation and number of the list of the corresponding document in accordance with Figure 11 b. Or a series of working drawings of typical nodes and a release number in accordance with Figure 11 in.
| Figure 10. | Figure 11. |
Above the image of the node indicate the mug of its designation in accordance with Figure 13a, if the node is depicted on the same sheet from where it is transferred, or 13b if it is made on another sheet.
The node that is a complete mirror reflection of another (main) execution is assigned the same designation as the main execution, with the addition of the "H" index.
| Figure 12. | Figure 13. |
5.5.5 Local species indicate the capital letters of the Russian alphabet, which are applied next to the arrow indicating the direction of the view. The same designations are applied to images of species.
5.5.6 For each type of images (cuts and sections, nodes, fragments), an independent numbering order is used or alphabetic designations.
5.5.7 In the image (plan, facade or section), from where a fragment is taken out, the corresponding place is noted, as a rule, a figure bracket in accordance with Figure 14.
The name and sequence number of the fragment are applied under the curly bracket or on the shelf of the lifting line, as well as above the corresponding fragment.
Figure 14.
5.5.8 Images to the axis of symmetry of symmetric plans and facades of buildings and structures, arrangement of structural elements, plans for the location of technological, energy, sanitary and other equipment are not allowed.
5.5.9 If the image of the cut, cross section, node, type or fragment is placed on another sheet, then after designation, the number of this sheet is indicated in brackets in accordance with Figures 10, 11a, 12 and 14.
5.5.10 Images allowed to rotate. At the same time, in the names of images in the drawings, the conditional graphic designation "turned" does not lead
According to GOST 2.305, if the position of the image is defined uniquely, i.e. oriented by the coordination axes and / or high-altitude stamps.5.5.11 If an image (for example, a plan) does not fit on a sheet of adopted format, it is divided into several sections by placing them on separate sheets.
In this case, on each sheet, where the image section is shown, lead a scheme of a whole image with the necessary coordination axes and the symbol (shading) of the image section shown on this sheet in accordance with Figure 15.
Note - If the drawings of the image sections are placed in different basic sets of work drawings, then over the sheet number indicates a complete designation of the corresponding main kit.
Figure 15.
5.5.12 If the plans of the floors of a multi-storey building have small differences from each other, then fully implement the plan of one of the floors, for other floors, only those parts of the plan are performed to show the difference from the plan shown in full.
Under the name of the partially depicted plan, record: "The rest, see the Plan (name of the fully depicted plan)."
5.5.13 In the name of the plans of a building or structure, the word "plan" and the netting of the clean floor or the floor number, or the designation of the appropriate secular plane (when performing two or more plans at different levels within the flood).
Examples
1 Plan for OTM. 0,000
2 Plan 2 floors
3 plan 3-3.
When performing a part of the plan in the title indicate axes that limit this part of the plan.
Example- Plan for OTM. 0,000 between axes 21-30 and aa-d
It is allowed in the name of the floor plan to indicate the purpose of the premises located on the floor.
5.5.14 In the names of the building cuts (structures), the word "section" and the designation of the corresponding section of the plane are 5.5.2.
Example- Cut 1-1
Note - In the names of products, the word "incision" does not indicate.
The names of the sections are digital or alphabetic designations of the sequential planes.
Example- 5 -5 B-B,a-A.
5.5.15 In the names of the facades, the building or structures indicate the word "facade" and the designations of the extreme axes, between which the facade is located.
Example- Facade 1.-12, facade 1-1, facade a -G.
It is allowed in the name of the facade to indicate its location, for example, "the main", "yard", etc.
5.5.16 The names of images are not emphasized in the drawings.
6 Rules for performing specifications in the drawings
6.1 To the layout of the elements of the collection structure, monolithic reinforced concrete design, to the drawings of the production equipment and / or pipelines, installations (blocks) of technological, sanitary and other equipment, and other drawings are specification in form 7 (Appendix K).
When performing drawings, the group method constitutes group specifications in form 8 (Appendix K).
6.2 The specification is placed, as a rule, on the list of drawings, where the schemes, plans for the location of equipment and pipelines, installation plans are depicted. It is allowed to perform the specification on separate sheets as the subsequent sheets of drawings.
6.3 In electronic models, if necessary, specifications and other tables in the drawings are allowed to be performed in the working space of the electronic model, taking into account the provisions of GOST 2.052. In this case, they are recommended to perform in a separate information level.
6.4 Specifications of construction products are according to GOST 21.501.
7 Rules for making changes
7.1 General
7.1.1 On the basis of the provisions of Section 7 of this Standard, standards of organizations that take into account the features of making changes to project documents will be developed depending on the amount of documentation, the conditions of document management and the CAD and the SED used.
7.1.2 Changing the document previously transferred to the customer is any correction, exception or adding any data to it without changing the designation of this document.
The designation of the document is allowed to change only when different documents are erroneously assigned the same designations or an error is made in the designation. Making changes to calculations is not allowed.
7.1.3 If a change in the document is unacceptable, a new document with a new designation must be released.
7.1.4 Any change in the document that causing any changes in other documents should simultaneously be accompanied by the introduction of appropriate changes to all interconnected documents.
7.1.5 Changes contribute to the original document.
7.1.6 The fact information change information indicates:
In paper documents - in the main inscription of these documents and / or in the Change Registration Tables;
In DE - in the detailed part of these documents;
In the column "Note" of documents and statements intended for accounting for documents.
7.2 Permission to make changes
7.2.1 Changing the document (including canceled it) is carried out, as a rule, based on permission to make changes (hereinafter - permission). Permission is performed on paper forms 9 and 9a (application L) or as DE.
The resolution is registered in accordance with GOST R 21.1003.
7.2.2 Permission approves the head of the organization - a document developer or another official authorized.
The resolution is the basis for receiving the original documents and the changes in them.
7.2.3 The scripts of permits on paper are stored in the archive of the organization.
7.2.4 Changes to each document (for example, the main set of work drawings, the specification of equipment, products and materials) are made on the basis of a separate resolution.
It is allowed to make one general permission to change, introduced simultaneously in several documents if the changes are interconnected or the same for all changeable documents.
Changes to the documents of the main set of work drawings decorated with separate documents (see 4.2.5), as well as documents of the Tom of Project Documentation are made on the basis of one general permission.
7.2.5 When making changes to DE, permission is allowed not to do, if the CAD and the EDD accounts and storing the versions of the document and the access control is ensured, excluding the possibility of unauthorized changes.
7.3 Amendments
7.3.1 Changes are indicated by sequence numbers (1, 2, 3, etc.). One sequence number of the Change is assigned to all changes that contribute to the document in one permission. It is indicated for the whole document, regardless of how many sheets it is completed.
7.3.2 When making changes to the DE script, any change is indexed as a new version of this document.
7.3.3 Changes in paper scripts of documents contribute:
Crossing;
Clearing (washing);
Painting with white;
Introduction of new data;
Replacement of sheets or all the document;
Introducing new additional sheets and / or documents;
Except for individual sheets of the document.
At the same time take into account the physical state of the original.
7.3.4 Changes to documents are made by automated and handwritten methods.
7.3.5 The handwritten method of change is made in paper scripts of documents in accordance with 7.3.9 - 7.3.16.
After making, the original should be suitable for making copies of the documentation of the appropriate quality methods of reprogram.
7.3.6 Making changes to DE produced by issuing a new version of a document with changes.
7.3.7 When making changes to an automated method, a new script is manufactured taking into account the changes made and retain its former designation.
The new script is also manufactured if there is not enough place for handwriting changes or a violation of the image clarity is possible when corrected.
If one or several sheets of the script is replaced or add or add, then they retain the inventory number assigned to the script.
When replacing all the script sheets, he is assigned a new inventory number.
7.3.8 Changes to the estimated documentation are carried out by an automated way to replace the entire document.
7.3.9 Changeable sizes, words, signs, inscriptions, etc. It is burned with solid thin lines and the new data is affixed.
7.3.10 When the image is changed (part of the image), it is reduced by a solid thin line forming a closed circuit, and crucifically crossed with solid thin lines in accordance with Figure 16.
A new image of the changed area is performed on a free field of a sheet or on another sheet without turns.
Figure 16.
7.3.11 A variable and additional sections of the image are assigned a designation consisting of a sequence number of the next document change and through the point of the sequence number of the variable (optional) portion of the image within this sheet. In this case, the new image of the changed area is assigned the designation of the changed image.
If a new image of the changed area is placed on another sheet, the changes assigned to it is preserved and in the table of changes of this sheet do not take into account.
7.3.12 Near each change, including near the space fixed by the cleaner (wash) or inks with white, outside the image or text is applied in the parallelogram the designation of the change (see Figure 16) and from this parallelogram conduct a solid thin line to the changed area .
It is allowed from the parallelogram with the designation of the change of the line to the changed area not to be carried out.
When making changes to text documents (in the text part of the documents), the line from the parallelogram is not carried out with the designation.
7.3.13 Changed the modified dimensions, words, signs, inscriptions, etc. are close to each other, and so on. Retires a solid thin line forming a closed circuit, without more than a crosslinking in accordance with Figure 17.
Figure 17.
7.3.14 If a new image of the modified area is placed on another sheet, then the replaced image also indicates the number of the leaf on which the new image is located (see Figure 16).
7.3.15 Over the new image of the changed area is placed in the parallelogram the designation of the change in the replaced image, and at the parallelogram indicate: "In return crushed."
If a new image of the changed area is placed on another sheet, then at a parallelogram indicate: "In addition to the listed on the sheet (the sheet number on which the replaced image is located)" in accordance with Figure 18.
Figure 18.
7.3.16 If a new image of the changed area is placed near the replaced, they are connected by liners with the notation with the designation of the change in accordance with Figure 19.
Figure 19.
Above the optional image is placed in the parallelogram the designation of the change, and at the parallelogram indicate: "Supplement" in accordance with Figure 20.
Figure 20.
7.3.17 When adding a new sheet of a text document, it is allowed to assign the number of the previous sheet with the addition of the next lower case letter of the Russian alphabet or through the Arabic digit point, for example 3a or 3.1.
In text documents containing mainly solid text, it is allowed when adding a new item to assign the number of the previous paragraph with the addition of the next lower case letter of the Russian alphabet, and with the exclusion of the item - to save the numbers of subsequent points.
7.3.18 When the total number of sheets of the document on its first sheet in the main inscriptions make appropriate fixes in the "Sheets" graph.
7.3.19 Data on changes made to the original indicate the change table placed in the main inscription (if available), and with a lack of space - in the additional table to it (see 5.2.6).
In the new (modified) version of the DE in the Change table indicate the data only on the last change.
7.3.20 When making changes to the documents, the change table is filled with sheets (sheet):
The first (title) of the new script, made in general instead of the old one;
Modified;
Released instead replaced;
Added again.
7.3.21 The change table indicates:
a) in the column "Izm." - Order number of document change. When replacing the original, the new regular serial number is affixed, based on the last number of the change specified in the replaced script;
b) in the column "count uch. " - the number of variable sections of the image on this sheet within the next change;
c) in the column "Sheet":
1) on sheets released instead of replaced, "deputy.";
2) on sheets added again, - "New";
3) When replacing all sheets of the original when manually making changes in the first (title) sheet - "All" (the table of changes on other sheets does not fill in this script), an automated way - "Deputy" On all sheets.
In other cases, the column "Sheet" put a fiber;
d) in the column "no doc." - permit designation;
e) in the column "Sub." - signature of the person responsible for the correctness of the change. When replacing all the sheets of the original automated method, the signature is affixed only on the first (title) sheet. The signature of the normocontroller is affixed on the field to cover the sheet (except for sheets released instead of replaced and new);
e) In the "Date" column, change changes.
7.3.22 The registration of changes in text documents is recommended to be carried out in the registration table of changes in form 10 (Appendix M), which is placed on a separate last sheet of document when making the first and subsequent changes.
7.3.23 When replacing sheets of documents issued by the main inscriptions in forms 3 - 5, the sheets released instead of replaced are signed in graphs 10 - 13 of the main inscriptions in accordance with the procedure provided for for newly developed sheets.
7.3.24 When canceling or replacing the sheets of a document on all canceled and replaced sheets of the original stamped stamp "canceled (replaced)" in the form given in GOST R 21.1003 (Appendix D), which is filled in accordance with the instructions given in the same place.
7.4 Features of making changes to project documentation
7.4.1 Amendments to project documentation are made according to 7.1 - 7.3, taking into account the provisions 7.4.2 - 7.4.8.
7.4.2 Changes to the project documentation previously transferred to the Customer, as a rule, make an automated way and implement:
Replacement, adding or exception of individual volume sheets;
Replacement (reissue) volume - with its full processing;
Release of additional volumes.
7.4.3 With the full processing of the section or subsection of project documentation, at the beginning of its textual part, it is recommended to provide information on the changes: the basis for making changes, a brief description of the changes made.
7.4.4 If the changes are made on the basis of a negative conclusion of the project documentation examination, then the "Explanatory Note" section includes a certificate with a description of the changes entered in the project documentation. The certificate must be signed by the person responsible for the preparation of project documentation, the chief project engineer.
7.4.5 Registration of changes (versions) of volumes generally produced in the table of registration of changes in form 11 (Appendix M), which is placed when making changes on its title page and cover. It is allowed to give the table only on the cover.
The state registration table does not take into account the corrections made to the statement of the composition of the project documentation in connection with the changes in other volumes of project documentation.
7.4.6 Information on changes in sheets of graphic documents indicates the column "Note" of the content of volume:
a) for replaced sheets when making a first change - "Izm. 1 (deputy) ", subsequent changes - additionally the next number of changes, separating them from the previous point with the comma.
Example- Change 1 (deputy);
b) for eliminated (canceled) sheets in the number of change - "(Annun.)".
Example- Change 1 (Annun.);
c) for additional sheets in the number of change - "(new)"
Example- Change 1 (new).
7.4.7 When performing additional volumes of project documentation, corrections contribute to the statement "The composition of the project documentation".
Information on changes in the statement of the composition of the project documentation in the content of volume do not lead.
7.4.8 Changes to the approved project documentation related to the change in the parameters of the construction object affecting its constructive reliability and security, and the need to reaffece project documentation, contribute by the Customer's decision on the basis of a new task for designing or additioning to the previously approved task for design.
7.5 Features of making changes to working documentation
7.5.1 Amendments to working documentation are made according to 7.1 - 7.3, taking into account the provisions 7.5.2 - 7.5.9.
7.5.2 When making changes to the sheets of the main set of work drawings in the statement of the working drawings of this kit in the "Note" column indicate:
For replaced, canceled and additional sheets - information in accordance with the transfers A) - B) 7.4.6;
For modified sheets (handwritten method), when making a first change - "Izm. 1 ", subsequent changes - additionally the next number numbers, separating them from the previous point with a comma.
Example- Change one; 2; 3.
In case of replacing sheet data sheets in the statement of the working drawings of this kit, it is allowed to provide information only about the last change in the sheets of the main kit.
7.5.3 If additional sheets include additional sheets in the main set of work drawings, then they are assigned the next ordinal numbers and recorded in the continuation of the statement of the work drawings of the corresponding main kit.
With a lack of space in the statement of work drawings for recording additional sheets, the continuation of the statement is transferred to the first of the additional sheets. At the same time, at the end of the statement of the working drawings placed in "General Data", they make an entry: "For the continuation of the statement, see the sheet (sheet number)", and the title: "The statement of the work drawings of the main kit (continued) is placed on the supplementary sheet .
When changing the names of the sheets make appropriate corrections in the Count "Name".
When making changes to the handwritten method, the number and names of the canceled sheets in the statement of the working drawings are shred out by an automated method - the Count "Name" for the annulled sheets is not filled.
7.5.4 When making changes to the documents of the main kit, decorated with individual documents, appropriate corrections to the statement of documents of the main set of work drawings.
7.5.5 When performing additional and cancellation of previously executed documents, corrections contribute to the section "The Acceived Documents" of the Lord of the reference and accompanying documents of the corresponding major set of work drawings.
When replacing reference documents in the working drawings (see 4.2.8), corrections make corrections to the appropriate section of the Vedomosti reference and the accompanying documents.
7.5.6 When performing additional and cancellation of previously completed main sets of work drawings make corrections to the statement of the main sets of work drawings.
7.5.7 In the tables of changes on sheets of general data, corrections made in the statement of general data in connection with the introduction of changes in the sheets of the main kit and the accompanying documents are not taken into account as plots of changes in accordance with 7.3.11.
7.5.8 Registration of changes in document documents issued by title sheets, also produced in the registration table of changes in form 11 (Appendix M), which is placed on the title page when making changes.
7.5.9 Copies of sheets (modified, additional and released instead of replaced sheets) Working documentation on paper guide are sent to organizations that were previously sent copies of documents, simultaneously with copies of the general data of the relevant basic set of work drawings refined in accordance with 7.5.2 - 7.5. .6.
In electronic form, organizations guide new versions of documents with changes (see 7.3.6).
8 Rules for issuing discharged documentation
8.1 Copies of textual and graphic materials of project documentation and reporting technical documentation for engineering surveys are brocked in Toms folded on A4 GOST 2.301 format.
Note - Under the stitching it means the placement of materials of project documentation on paper in binding or in solid folders with easy-to-lock mounts (locks).
8.2 Copies of documents of working documentation are equipped with a folder with polist, folded on A4 format, as a rule, separately for the main sets of work drawings.
It is allowed to stroke copies of working documents in the volume in accordance with 8.1 or into albums folded on A3 format.
The number of sheets included in the folder or album must correspond 4.1.5.
8.3 Each document, a volume or album, intended for a brochure, as well as the folder with the documents folded into it, make up the cover in form 12 (Appendix N). The cover is not numbered and not included in the total number of sheets.
8.4 The first sheet of a discharged document, as well as a volume consisting of several documents, an album or folder with working documentation, is a title list.
The title page is performed in form 13 (Appendix P). Examples of the performance of title sheets are shown in Figures P.1 and P.2 (Appendix P).
In the volume of project documentation, consisting of several independent documents, including the text part, the title list to the text part, as a rule, is not executed.
8.5 All sheets of a discharged volume (album) are recommended to numbered through the passage of sheets, starting from the title leaf. At the same time, the title page does not name. The sheet number is indicated in the upper right corner of the sheet of the sheet (see Appendix and).
In addition, text and graphic documents included in the (album) and having an independent designation should have a sequence numbering of sheets within a document with one designation in the main inscription or in footer (in accordance with 4.1.8).
8.6 When you recruit multiple documents in the form of volume, album, as well as in the folder after the title page, the content of the volume (album, folders), which is a list of documents included in that (album, folder). The content is performed in form 2 (application d) on the sheets of A4 format.
Documents in the content are recorded in the sequence of their acquisition in the album or folder. The graphic documents of the project and reporting technical documentation for engineering surveys are written pols. The cover and the title page in the content is not written.
In the column "Name" - the name of the document in full compliance with the name specified in the main inscription or on the title page;
In the Count "Note" - information about the changes made to the recorded documents, as well as the number of volume sheet on the pass-through numbering of TOM sheets in accordance with 8.5, from which the document begins.
If the pass-through numbering is not performed, then in the "Note" column, the total number of sheets of each document leads. At the end of the content, there is a total number of sheets included in the (album, folder).
The first sheet of volume content (album, folders) is drawn up the main inscription in form 5 (application g), follow-up - in form 6 (application g). The content is assigned a designation that consists of a volume designation (album, folders) and through the defisis of cipher "C".
Example - 2345-ROM2-C; 2345-11-kzh.i-s; 2345-11-rs.ol-s; 2345-11-TXN
In column 5, the main inscription indicate the "content of volume" or, accordingly, the "album content" and "content of the folder" and further - the number of the corresponding volume, album or folder (if available).
8.7 Title sheets of volumetric volume documentation are written in signatures:
Supervisor or chief engineer organization;
Persons responsible for the preparation of project documentation, such as the chief engineer (architect) of the project.
Title sheets of working documents are issued by the signed by the person responsible for the preparation of working documentation, the chief engineer (architect) of the project.
The title page of the technical report on the results of engineering surveys is issued by the signature of the head of the organization or its deputy and, if necessary, other officials.
The title sheets of copies of the documentation transmitted to the customer are assumed by the print print of the organization that prepared this documentation.
8.8 The composition of the project documentation, as well as the composition of the reporting technical documentation on the results of engineering surveys, lead in the statement performed in form 14 (Appendix C) on the A4 sheets.
The statements lead a consistent list of volumes of project or reporting technical documentation for engineering surveys.
The first sheet of statement is drawn up the main inscription in form 5 (Appendix G), follow-up - in form 6 (application g).
The composition of the project documentation is assigned the designation consisting of the basic designation of project documentation and through the defisis of cipher "SP".
Example - 2345-joint
When blocking a statement in a separate volume, it is made in cover and title sheet in accordance with 8.3 and 8.4. The volume number on the cover and the title page does not indicate.
The composition of the reporting technical documentation on the results of engineering surveys is assigned a designation consisting of the basic designation of documentation and through the Defisc of the cipher "SD".
Example - 2344-CD
Sections of project documentation
A.1 CIFRES OF STEPS OF THE PROJECT DOCUMENTATIONS ON CAPITAL CONSTRUCTION OBJECTIVES OF PRODUCTION AND ENTERPRISTING DESSIONS Listed in Table A.1.
Table A.1.
| room | Cipher |
|
| Explanatory note | ||
| Land Planning Organization Scheme | ||
| Architectural solutions | ||
| Constructive and volume planning solutions | ||
| Information about engineering equipment, engineering and technical support networks, a list of engineering and technical measures, the content of technological solutions | ||
| Project of the organization of work on demolition or dismantling of capital construction facilities | ||
| List of environmental protection measures | ||
| Disabled access activities | ||
| Requirements for ensuring the safe operation of the capital construction facility | ||
| Estimation for the construction of capital construction facilities | ||
| Events to ensure compliance with the requirements of the energy efficiency and requirements of the equipment of buildings, buildings and structures to the instruments of accounting of energy resources used | ||
| List of civil defense activities, measures to prevent natural and man-made emergencies, measures to counter terrorism | ||
| Other documentation established by legislative acts of the Russian Federation | ||
| Note - Partition numbers 10 1 and 11 1 are allowed to bring 10 (1), 11 (1) or 10-1, 11-1. |
||
A.2 Encipers of project documentation sections on linear objects are shown in Table A.2.
Table A.2.
| room | Name of the project documentation | Cipher |
| Explanatory note | ||
| Draft Strip Top | ||
| Technological and structural solutions of a linear object. Artificial constructions | ||
| Buildings, buildings and structures included in the infrastructure of a linear object * | ||
| Project organization of construction | ||
| Project of the organization of work on demolition (dismantling) of a linear object | ||
| Environmental protection measures | ||
| Fire Safety Activities | ||
| Estimation for construction | ||
| Other documentation in cases provided for by federal laws, including: | ||
| List of civil defense activities, measures to prevent emergency situations of natural and man-made character, measures to counteract terrorism | ||
| Declaration of industrial safety of hazardous production facilities | ||
| Safety Declaration of hydraulic structures | ||
| * Project documentation of buildings, buildings and structures are developed in accordance with the composition of the documentation on Table A.1. |
||
Note - If necessary, code documentation sections are allowed to be denoted by the letters of the Latin alphabet in accordance with the rules established in the standards of organizations.
Brands of the main sets of work drawings
Table B.1.
| Name of the main set of work drawings | Note |
|
| General Plan and Transport Construction | When combining work drawings of the master plan and transportation structures |
|
| General plan | ||
| Car roads | ||
| Railways | ||
| Construction facilities | When combining workers' drawings of automotive, iron and other roads |
|
| Architectural and construction solutions | When combining work drawings of architectural and design solutions (except KM) |
|
| Architectural solutions | ||
| Interiors | Workers drawings can be combined with the main set of the Arm or AC |
|
| Constructs are reinforced concrete | ||
| Metal designs | ||
| Metal designs detail | ||
| Wooden designs | ||
| Hydraulic solutions | ||
| Anticorrosive protection of buildings, structures | ||
| Power supply | ||
| Outdoor electric light | ||
| Power equipment | ||
| Electric lighting (internal) | ||
| Exterior Water Supply Networks | ||
| Outdoor sewage networks | ||
| Outdoor network of water supply and sewage | When combining workers' drawings of external water supply and sewage networks |
|
| Internal water supply and sewage systems | ||
| Firefighting | ||
| Heating, ventilation and air conditioning | ||
| Air supply | ||
| Dustovation | ||
| Fooling | ||
| Teplomechanical solutions | Boiler houses, CHP, etc. |
|
| Heat mechanical solutions of thermal networks | ||
| Wired communications * | The names of the main sets and the designations of the brands are taken by Appendix A GOST R 21.1703 |
|
| Radio communication, broadcasting and television | ||
| Fire alarm | ||
| Security and Security and Fire Alarm | ||
| Outdoor gas pipelines | ||
| Gas supply (internal devices) | ||
| Production technology | ||
| Technological communications | When combining workers' drawings of all technological communications |
|
| Anticorrosive protection of technological apparatus, gas ducts and pipelines | ||
| Thermal insulation of equipment and pipelines | ||
| Automation complex | When combining workers' drawings of automation of various technological processes and engineering systems |
|
| Automation +. | The names of the main sets and the designations of the brands are taken by Appendix A GOST 21.408 |
|
| Hydrogenic linear structures * | The names of the main sets and the designations of stamps are taken by Appendix A GOST 21.709 |
|
| * There are general names of objects. Notes 1 If necessary, additional brands of the main sets of work drawings can be appointed. At the same time, it is recommended to include no more than three capital letters of the Russian alphabet corresponding to, as a rule, the initial letters of the name of the main set of work drawings. 2 If necessary, the brand of the main sets of work drawings is allowed to be denoted by the letters of the Latin alphabet or digital codes in accordance with the rules established in the standards of organizations. |
||
Encipers of the attached documents
Table B.1.
| Name of the attached document | |
| Specification of equipment, products and materials | |
| Sketch drawing of the general type of the inepar | |
| Construction Product Drawing | |
| Poll sheet, overall drawing | |
| Local estimates | |
| Calculations * | |
| * Calculations, as a rule, are not included in the working documentation, unless otherwise defined in the contract (contract) and the design task. Notes 1 Sifters of other types of attached documents are given in the relevant standards of SPDS or standards of organizations. 2 is allowed, if necessary, ciffers of the attached documents denote the letters of the Latin alphabet in accordance with the rules established in the standards of organizations. |
|
Appendix G.
(mandatory)
Vedomosti shared data on working drawings
Form 1 - statement of working drawings of the main kit
Statement of specifications
G.1 In the statement of the working drawings of the main kit indicate:
In the column "Sheet" - the sequence number of the sheet of the main set of workers drawings;
In the column "Name" - the name of images placed on a sheet, in accordance with the names given in the main inscription of the sheet;
In the Count "Note" - additional information, such as changes made in the working drawings of the main kit.
G.2 in the statement of specifications indicate:
In the column "Sheet" - the number of the main set of work drawings on which the specification is placed;
In the Count "Name" - the name of the specification in exact accordance with its name specified in the drawing;
In the Count "Note" - additional information, including changes made in the specification.
Form 2 - statement of the main sets of work drawings
The statement of reference and accompanying documents
Vedency of documents of the main set of work drawings
G.3 In the statement of the main sets of work drawings indicate:
In the graph "Designation" - the designation of the main set of working drawings and, if necessary, the name or distinctive index of the organization that issued a document;
In the column "Name" - the name of the main set of work drawings;
In the column "Note" - additional information, including changes in the main sets of work drawings.
G.4 The statement of reference and attached documents indicate:
In the graph "Designation" - the designation of the document and, if necessary, the name or distinguishable index of the organization that issued the document;
In the column "Name" - the name of the document in exact accordance with the name indicated on the title page or in the main inscription;
In the column "Note" - additional information, including the changes made to the recorded documents that are part of the working documentation. For documents in electronic form indicate, if necessary, the identifier of the file (files).
G.5 In the statement of documents of the main set of work drawings indicate:
In the column "Designation" - the designation of the document;
The "Name" column is the name of the document in accordance with the name specified in the main inscription. For graphic documents consisting of several sheets, the names of images placed on each sheet are also given in accordance with the names given in the main inscription of the sheet;
In the column "Note" - additional information, including changes made to recorded documents, and, if necessary, the total number of sheets of the document. For documents in electronic form indicate, if necessary, the identifier of the file (files).
G.6 Sizes Count statements, if necessary, can be changed at the discretion of the developer.
G.7 is allowed, if necessary, include additional graphs (columns), for example "count. sheets "etc.
G.8 When filling out the statements by an automated way, horizontal lines, distinctive lines, allowed not to be carried out. In this case, it is necessary to observe the interval of at least one discharge of the press between the texts of the adjacent lines.
Appendix D.
(mandatory)
The list of ECC standards subject to accountable when performing graphic
and text documentation for construction
Table D.1
| Designation and name of the standard | Conditions for applying Standard |
| GOST 2.004-88 Unified system of design documentation. General requirements for the implementation of design and technological documents on the printing and graphic devices of the Output | |
| GOST 2.051-2006 Unified system of design documentation. Electronic documents. General provisions | |
| GOST 2.052-2006 Unified system of design documentation. Electronic model model. General provisions | |
| GOST 2.101-68 Unified system of design documentation. Types of products | |
| GOST 2.102-68 Unified system of design documentation. Types and completeness of design documents | Taking into account the provisions of GOST 21.501, relating to the performance of the drawings of construction products |
| GOST 2.105-95 Unified system of design documentation. General requirements for text documents | Taking into account the provisions of sections 4, 5 and 8 of this standard |
| GOST 2.109-73 Unified system of design documentation. Basic requirements for drawings | |
| GOST 2.113-75 Unified system of design documentation. Group and Basic Design Documents | Taking into account the provisions of GOST 21.501 |
| GOST 2.114-95 Unified system of design documentation. Technical conditions | Taking into account the provisions 5.2.1, 5.2.2, 5.2.5 - 5.2.7 and Section 8 of this Standard. Provisions 3.7.1 and 3.8 GOST 2.114 do not take into account |
| GOST 2.301-68 Unified system of design documentation. Formats | Taking into account the requirements of the relevant SPDS standards |
| GOST 2.302-68 Unified system of design documentation. Scale | Taking into account the provisions 5.1.6 of this Standard |
| GOST 2.303-68 Unified system of design documentation. Lines | Taking into account the provisions 5.1.3 of this standard |
| GOST 2.304-81 Unified system of design documentation. Drawing fonts | Taking into account the provisions 5.1.5 of this Standard |
| GOST 2.305-2008 Unified system of design documentation. Images - species, cuts, sections | Taking into account the provisions of 5.5 of this Standard |
| GOST 2.306-68 Unified system of design documentation. Designations Graphic materials and rules for their application in drawings | Taking into account the provisions of GOST 21.302, Tables 4 and 5 |
| GOST 2.307-2011 Unified system of design documentation. Differences and limit deviations | Taking into account the provisions 5.4.1 - 5.4.4 of this Standard |
| GOST 2.308-2011 Unified system of design documentation. Specifying forms and location of surfaces | Taking into account the provisions of GOST 21.113 |
| GOST 2.309-73 Unified system of design documentation. Roughness designation surfaces | |
| GOST 2.310-68 Unified system of design documentation. Application in drawings of designations of coatings, thermal and other types of processing | |
| GOST 2.311-68 Unified system of design documentation. Image of thread | |
| GOST 2.312-72 Unified system of design documentation. Conditional images and designations of welded joints | |
| GOST 2.313-82 Unified system of design documentation. Conditional images and notation of all-point connections | |
| GOST 2.314-68 Unified system of design documentation. Indications in drawings on marking and branding products | |
| GOST 2.315-68 Unified system of design documentation. Images simplified and conditioner fasteners | |
| GOST 2.316-2008 Unified system of design documentation. The rules for applying inscriptions, technical requirements and tables on graphic documents. General provisions | Taking into account the provisions 5.4.5 - 5.4.7 of this Standard |
| GOST 2.317-2011 ECCD. Axonometric projections | |
| GOST 2.501-88 ECCD. Rules for accounting and storage | In the form of the inventory book, subscriber card and instructions for folding drawings |
| GOST 2.511-2011 Unified system of design documentation. Rules for the transfer of electronic design documents. General provisions | |
| GOST 2.512-2011 Unified system of design documentation. Rules for performing a data packet for transmitting electronic design documents. General provisions | |
| Note - The conditions for the application of ECC standards of the classification group 7 are defined by the SPDS standards, in which links to these standards are given. |
|
List of permissible cuts of words used in graphic documents
(Supplement K.GOST 2.316 )
Table E.1.
| Full name | Abbreviation | Full name | Abbreviation |
| Highway | Equipment | ||
| Canceled | |||
| Antisaismic seam | |||
| Architect | |||
| Asphalt concrete | calculate Narr. |
||
| Concrete, concrete | Sanitary-technical | san. tehn |
|
| Ventilation camera | ventscamera | Toilet | san. knot. |
| Capacity | Navy. (C, T) | ||
| Chief Engineer | GL Ing. (about) | Well | |
| Chief Engineer (Architect) of the Project | GUI (HAP) (O) | Snow | |
| Chief Specialist | GL specialist. (about) | Temperature seam | |
| Technological | |||
| Expansion joint | |||
| Director | |||
| Document | dock. (T, O) | Rail head level | ur. G. R. (and) |
| Permissible | The level of soil (underground) water | ||
| Railway | Ground level | ||
| Railway | Pure floor level | ||
| Reinforced concrete, reinforced concrete | |||
| Head | Foundation | ||
| Insulation, isolation | Cement, cement | ||
| Institute | Cement concrete | ||
| Design | |||
| Coefficient | |||
| Efficiency | Plaster | ||
| Staircase, stairs | Crushed stone, rubble | ||
| Workshop (in project organizations) | Electric | ||
| Materials | mat-lies | eL-T (and, T) |
|
| Mounting | |||
| nORM. Nagr. | |||
| Notes 1 abbreviations marked with the sign (O) apply only in the main inscription; (T) - in the tables; (C) - with numbers or ciphers; (and) - in graphic images 2 reductions in the words specified in this table and GOST 2.316 is allowed to be indicated in text documents broken into graphs. |
|||
Appendix J.
(mandatory)
Main inscriptions and additional graphs for them
Form 3 - for sheets of major sets of work drawings, graphic documents of project documentation and graphic documents on engineering surveys
Note - For graphic documents on engineering surveys, the entry "N. counter." ("Normo-Control") in the main inscription is allowed not to be performed.
Form 4 - for the drawings of building products (first sheet)
Form 5 - for sketchy drawings of general types of non-type products, all types of text documents (first or title sheet)
Note - The main inscription in form 5 is allowed to use for graphic documents on engineering surveys not used in the design as a graphic basis.
Form 6 - for drawings of construction products, sketching drawings of common types of non-type products and all types of text documents (subsequent sheets)
Note - The main inscription in form 6 is allowed to be used for subsequent sheets of graphic documents on engineering surveys not used in design as a graphic basis.
In the graphs of the main inscription and additional graphs to it (the number of the graph is listed in brackets) lead:
In column 1 - the designation of the document, including a text or graphical document of the section, subsection of project documentation, the main set of work drawings, drawing of the product, etc.;
In column 2 - the name of the enterprise and, if necessary, its parts (complex), the housing and civil complex or another construction object, which includes a building (structure), or the name of the neighborhood;
In column 3 - the name of the building (structures) and, if necessary, the type of construction (reconstruction, technical re-equipment, overhaul);
In column 4 - the name of images placed on this sheet, according to their name in the drawing. If one image is placed on the sheet, it is allowed to bring it only in column 4.
Names of specifications and other tables, as well as text indications related to images, in column 4 do not indicate (except when specifications or tables are made on separate sheets). On the sheet (sheets) of general data on working drawings in column 4, "General data" is recorded. In the case provided for in 5.2.3, in column 4 lead the name of the document or the non-type product;
In column 5 - the name of the product and / or the name of the document;
In column 6 - the conditional designation of the type of documentation: P - for project documentation, P - for working documentation.
For other types of documentation, the graphs do not fill or lead symbols established in the standards of the organization;
In column 7 - the sequence number of the sheet of document. On documents consisting of one sheet, the graph is not filled;
In column 8 - the total number of document sheets. The graph is filled only on the first sheet;
In column 9 - the name or distinctive index of the organization that has developed a document;
The column 10 is the nature of the work performed by the person signed by the document, in accordance with Forms 3 - 5. In free lines, at the discretion of the project organization, the positions of specialists and managers responsible for developing and verifying the document are given. In the line under the record "developed" instead of office, it is allowed to recording "Checked".
Signatures of the person who has developed this document and normocontroller are mandatory.
The lower line provides the position of person who approved the document, such as the chief engineer (architect) of the project, the head of the department or other responsible for this document (sheet) of the official.
Signatures of the person responsible for the preparation of project or working documentation (the chief engineer (architect) of the project) are binding on sheets of general data on working drawings, the most significant sheets of the graphic part of the project documentation and work drawings;
In graphs 11 - 13 - surnames and signatures of the persons listed in column 10 and the date of signing. Signatures of other officials and matching signatures are placed on the field to cover sheet;
In columns 14 - 19 - information about the changes that are fill in accordance with 7.3.21;
In column 20 - the original number of the original;
In column 21 - the signature of the person who accepted the script for storage, and the acceptance date;
In column 22 - the inventory number of the original document, in return for which a new script was released;
In column 23 - the designation of the material of the part (the graph is filled only in the drawings of the parts);
In column 24 - a mass of the product shown in the drawing, in kilograms without specifying a unit of mass. The mass of the product in other units of mass leads with an indication of the mass unit.
Example- 2.4 t;
- in column 25 - scale (affilted in accordance with GOST 2.302);
In column 26 - the designation of the format of the sheet according to GOST 2.301. For an electronic document, the sheet format is indicated on which the image will correspond to the set scale;
In column 27 - the brief name of the customer organization.
Notes
1 In columns 13, 19, 21, when specifying the calendar dates on paper, the year indicates the last figures, for example, 02/02/12.
2 Count 27, specified by the stroke line, is administered if necessary.
3 columns "coordinated" (10 - 13) located on the field for the binder is allowed to bring only those sheets where it is necessary. If necessary, they repeat them.
4 is allowed, if necessary, change the location and dimensions of additional graphs placed on the binder field, in accordance with GOST 2.004.
Appendix I.
(mandatory)
Location of the main inscription, additional graph to it
and sizes of frames on sheets
Figure and.1 - location of the main inscription, additional graph and frame size
Figure and.2 - The allowable location of the main inscription on the A4 sheet
Appendix K.
(mandatory)
Specifications
Form 7 - Specification
Form 8 - Group Specification
Q.1 in specifications indicate:
In the column "Pos." - positions (brands) of structural elements, installations;
In the graph "Designation" - the designation of the main documents on the elements of structures, equipment, products or standards (technical conditions) on them recorded in the specification (technical conditions) on them;
In the column "Name" - the name of the elements of structures, equipment, products, materials and their designations (brands), as well as, if necessary, the technical specifications of the equipment and products. It is allowed to the group of the same elements indicate the name once and emphasized it.
The specification records materials directly included in the specified design, product, etc.
In the specification made in electronic form, a horizontal trait included in the designation of materials (rolled, pipes, etc.) is allowed to be replaced by oblique line (/);
In the column "count." Form 7 - the number of items.
In the column "count." Forms 8 - instead of dots, write "according to the scheme", "on the floor", etc., and below - the ordinal numbers of the location or floors;
In the column "Mass., Kg" - a lot of kilograms. It is allowed to give a mass in tons, but indicating a mass unit;
In the Count "Note" - additional information, such as a unit of mass.
K.2 Sizes Count Specifications at the discretion of the developer, if necessary, can be changed.
K.3 when the specifications are filled with an automated way of a line, distinguishing horizontal lines, allowed not to be carried out.
Permission to make changes
Form 9 - permission to make changes (first sheet)
Form 9A - permission to make changes (subsequent sheets)
L.1 in permission graphs indicate:
In column 1 - the designation of the permission consisting of the sequence number of permission on the registration book of permissions according to GOST R 21.1003 and through a dividing sign (a hyphen, inclined line, etc.) - the last two digits of the year.
Example - 15-12; 15/12;
In column 2 - the designation of the document in which the change makes;
In column 3 - the name of the construction object;
In column 4 - another serial number assigned to changes that contribute to the document in one permission. It is indicated for the entire document, regardless of how many sheets it is completed. The ordinal numbers of the changes are denoted by Arabic figures;
In column 5 - numbers of sheets of a document in which changes make;
In column 6 - the content of the change in the form of a text description and / or graphic image;
In column 7 - the code of the cause of the change in accordance with Table L.1.
Table l.1
It is allowed to change the cause of the change not to indicate. In this case, the graph is fought;
In column 8 - additional information;
In columns 9 - 11 - the names of persons signing permission, their signatures and the date of signing;
In column 12 - the name of the project organization and the division (department), which resolved;
In columns 13 - 16 - the name of the relevant units or organizations, the posts and the names of the persons in the prescribed manner agree on permission, their signatures and the date of signing, as well as the signature of the normocontroller;
In column 17 - the sequence number of the resolution sheet. If the resolution consists of one sheet, the graph is not filled;
In column 18 - the total number of resolution sheets.
L.2 is allowed for subsequent sheets permission to use form 9.
Notes
1 is allowed to supplement the form of graphs to identify the resolution in electronic form. Location and dimensions Count Project organization establishes independently.
2 In columns 11, 16, when specifying the calendar date on paper, the year indicates the last two figures.
Registration tables
Form 10 - Change Registration Table (Text document)
M.1 Sizes Count table in form 10 Sets the document developer.
M.2 In the graphs of the Change registration table indicate:
In the column "Ime." - the sequence number of document change;
In the graphs "sheet numbers (pages) of modified, replaced, new, canceled" numbers of sheets (pages), respectively, modified, replaced, added and canceled for this permission.
When replacing all the sheets of the script (with the next order number of the document change), "all" indicates the "replaced" column. In the rest of the graphs they put a fiber;
In the column "Total sheets (pages) to the dock." - the number of sheets (pages) in the text document after making changes;
In the column "Dock number" - permit designation;
M.3 When replacing all the script sheets, the Changes Registration Table in form 10 do not reproduce the number of changes and other data relating to all the changes previously contributed.
Form 11 - Change Registration Table (Title List and Cover)
M.4 In the graph of the registration table of changes in form 11 indicate:
In the column "Ime." - sequence number of changes in document or volume;
In the column "No. Doc." - designation of permission to make changes in accordance with the instructions in the application l;
In the column "Sub." - signature of the person responsible for the correctness of the change;
In the "Date" column - the date of change.
M.5 If necessary, the number of rows can be increased.
M.6 When replacing a document or volume in the registration table in the form 11 form, do not reproduce the number of changes and other data related to all previously added changes.
Cover
H.1 on the cover leads the following details:
Field 5 - the name of the object of capital construction and, if necessary, the type of construction. The name of the construction object on the cover must comply with the information provided in graphs 2 and 3 of the main inscription (see Appendix G);
Field 9 - volume number on the statement "The composition of the project documentation" or "The composition of the reporting documentation on the results of engineering surveys" (if available);
Field 10 - year of issue of the document;
Field 11 - To place the registration table of changes in the form 11 of the application M (if necessary).
H.2 The dimensions of the fields 1 - 11 are set arbitrarily; The lines of the fields specified in the form are not applied; Numbers and names of fields do not indicate.
N.S. is allowed to provide additional details and attributes in accordance with the requirements established in the standards of the organization.
H.4 Cover sizes are taken depending on the volume format, folder or album, to which it is performed.
Title page
P.1 On the title page, the following details lead:
Field 1 - abbreviated, and in its absence - the full name of a higher organization (if available); indicate, as a rule, for state organizations;
Field 2 - logo (optional), the full name of the organization prepared by the document;
Field 3 - number and date of issuance of a certificate of admission to the relevant types of work (on the preparation of project documentation or surveys), which influence the safety of the object of capital construction;
Field 4 - a brief name of the customer organization (if necessary). Name indicate: "Customer - the name of the organization-customer";
Field 5 - the name of the object of capital construction and, if necessary, the type of construction. The name of the construction object on the title page must comply with the information provided.
in graphs 2 and 3 of the main inscription (see Appendix G);
Field 6 - type of documentation (if necessary);
Field 7 - document name;
Field 8 - document designation;
Field 9 - volume number on the statement "The composition of project documentation" or "Composition of reporting documentation for engineering research" (if available);
Field 10 - posts responsible for the development of the document;
Field 11 - signatures of persons indicated on the field 10, performed according to GOST R 6.30. This field also includes the registering of the organization that prepared the document;
Field 12 - initials and surnames of the persons specified on the field 10;
Field 13 - year of issue of the document;
Field 14 - to place the registration table of changes in the form 11 of the application M (if necessary);
Field 15 - for additional graph of the main inscription in accordance with the application of J. The information contained in these graphs is allowed to bring in another form in accordance with the requirements established in the standards of the organization.
P.2 The size of the fields 1 - 14 is set arbitrarily; The lines of these fields specified in the form are not applied, the numbers and names of the fields do not indicate.
C.3 is allowed to make a title page without frames.
P.4 is allowed to bring additional details and attributes in the title page in accordance with the requirements established in the standards of the organization.
P.5 The dimensions of the title leaf are taken depending on the volume format, the folder or album to which it is performed.
Appendix R.
(Reference)
Examples of the performance of title sheets *
* The examples are conditional.
Figure P.1 - Example of the title Tom of Project Documentation
Figure P.2 - Example of the title sheet of volume (folders) of working documentation
The composition of the project documentation.
The composition of the reporting documentation on the results of engineering surveys
C.1 in Vedomosti indicate:
In the column "Tom number" - the sequence number of the volume volume or volume number, which includes the section number and, if there is a number of subsection, parts, books (see 4.1.1, 4.1.3), separated by points.
Example - 1, 2.1, 2.2, 5.5.1, 5.5.2;
- in the graph "Designation" - the designation of the document (volume) indicated on its title page, and, if necessary, the name or distinctive index of the organization that issued the document;
In the column "Name" - the name of the document (volume) in exact accordance with the name specified on its title sheet;
In the column "Note" - additional information, including changes made.
C.2 Sizes Count Vedomost at the discretion of the developer, if necessary, can be changed.
C.3 When filling out the statement by an automated way, horizontal lines, distinctive lines, allowed not to be carried out.
Bibliography
Keywords: project documentation, work documentation, basic requirements, main set of work drawings, basic inscription, making changes, title sheet
GOST 21.101-97
UDC 691: 002: 006.354
Interstate standard
System of design documents for construction
Basic requirements for project and working documentation
System of Design Documents for Construction.
Main Requirements for Design and Working Documents
OX 01.100.30
Date of introduction 1998-04-01
Preface
1 Developed by a state-owned enterprise - the center of the methodology, rationing and standardization in construction (GP Central SNS) Gosstroy Russia
Department of Development of Scientific and Technical Policy and Design and Exploration Works Gosstroy Russia
2 Adopted by the Interstate Scientific and Technical Commission for Standardization, Technical Registration and Certification in Construction December 10, 1997.
3 was put into effect from April 1, 1998 as the State Standard of the Russian Federation by the Resolution of the Gosstroy of Russia from 29.12.97 No. 18-75
4 Instead of GOST 21.101-93
1 area of \u200b\u200buse
This standard establishes the basic requirements for project and working documentation for the construction of enterprises, buildings and structures of various purposes.
The general rules for implementing graphic and text documentation established in Section 5 of this Standard are also applied to the reporting technical documentation on engineering surveys for construction.
GOST 2.004-88 ECCD. General requirements for the implementation of design and technological documents on the printing and graphic devices of the Output
GOST 2.101-68 ECCD. Types of products
GOST 2.102-68 ECCD. Types and completeness of design documents
GOST 2.105-95 ECCD. General requirements for text documents
GOST 2.108-68 ESKD. Specification
GOST 2.109-73 ECCD. Basic requirements for drawings
GOST 2.113-75 ECCD. Group and Basic Design Documents
GOST 2.114-95 ECCD. Technical conditions
GOST 2.301-68 ECCD. Formats
GOST 2.302-68 ECCD. Scale
GOST 2.303-68 ECCD. Lines
GOST 2.304-81 ECCD. Drawing fonts
GOST 2.305-68 ECCD. Images - species, cuts, sections
GOST 2.306-68 ECCD. Designations Graphic materials and rules for their application in drawings
GOST 2.307-68 ECCD. Differences and limit deviations
GOST 2.308-79 ECCD. Note on drawings tolerances forms and location of surfaces
GOST 2.309-73 ESKD. Roughness designation surfaces
GOST 2.310-68 ECCD. Application in drawings of designations of coatings, thermal and other types of processing
GOST 2.311-68 ECCD. Image of thread
GOST 2.312-72 ECCD. Conditional images and designations of welded joints
GOST 2.313-82 ECCD. Conditional images and notation of all-point connections
GOST 2.314-68 ECCD. Instructions in the drawings on the labeling and branding of products
GOST 2.316- 68 ECCD. Rules for applying in drawings of inscriptions, technical requirements and tables
GOST 2.317-69 ECCD. Axonometric projections
GOST 2.410-68 ECCD. Rules for performing drawings of metal structures
GOST 2.501-88 ECCD. Rules for accounting and storage
GOST 21.110-95 SPDS. Specification of equipment, products and materials
GOST 21.113-88 SPDS. Characteristics of accuracy
GOST 21.114-95 SPDS. Rules for performing draft drawings of common types of non-type products
GOST 21.203-78 SPDS. Rules for accounting and storage of original project documentation
GOST 21.501- 93 SPDS. Rules for the implementation of architectural and construction work drawings.
3 General documentation requirements
3.1 The composition and content of project documentation for the construction of enterprises, buildings and structures is established by the current construction norms and regulations.
3.2 The working documentation for the construction of a building or structure in the general case includes:
a) workers drawings intended for the production of construction and installation work;
b) working documentation for construction products according to GOST 21.501;
c) sketch drawings of common types of non-type products according to GOST 21.114 *;
d) specifications of equipment, products and materials according to GOST 21.110;
e) another accompanying documentation provided for by the relevant standards of the project documentation system for construction (SPDS);
e) estimated documentation on established forms.
4 General Requirements for the Acquitations of Documentation
4.1 Project documentation
4.1.1 Project documentation for approval (stage-project, approved by part of the working draft), is equipped in Tom, as a rule, according to individual sections provided for by the construction regulations and regulations. Each volume is numbered by Arabic numbers.
Example - Volume 1 - General Explanatory Note
Volume 2 - general plan and transport
If necessary, volumes are divided into parts. In this case, the volume is numbered by type: volume 1.1, volume 1.2.
4.1.2 Text and graphic materials included in the complete, as a rule, in the following order:
Cover;
Title page;
Project composition;
Explanatory note;
The main drawings provided for by the construction standards and regulations.
The rules for designing the cover, the title list, the content and composition of the project are given in section 9.
4.1.3 Each text and graphical document included in the one is assigned the designation that indicates the title page and in the main inscriptions.
The designation includes a basic designation installed on the system currently operating in the organization, and through the hyphen - brand and / or code section of the project. The brands of the project sections are made by analogy with the brands of the main sets of work drawings given in Appendix A.
Examples
1. 2345-PZ Section "General Explanatory Note"
2. 2345-GT section "General Plan and Transport"
3. 2345-12-AC Section "Architectural and Construction Solutions",
PZ - project section cipher;
GT and AC - project sections brands.
________________
4.1.4 Text and graphic materials, as a rule, include on sheets folded according to A4 GOST 2.301.
Each volume includes no more than 250 sheets of A4 format, 150 sheets of A3 format, 75 sheets of format A2 and 50 sheets of A1 format.
4.1.5 General requirements for the execution of graphic documentation are given in section 5.
Text documents are performed according to GOST 2.105, taking into account the requirements of Section 5 of this Standard.
4.2 Workers drawings
4.2.1 Working drawings intended for the production of construction and installation work are combined into kits (hereinafter main sets) on stamps in accordance with Appendix A.
4.2.2 The main set of work drawings of any brand can be divided into several basic sets of the same brand (with the addition of the sequence number) in accordance with the process of organizing construction and installation work.
Example - AC1; AC2; Kzh1; Kzh2.
4.2.3 Each basic set of working drawings is assigned the designation, which includes the basic designation installed on the system currently in force, and through the hyphen - the brand of the main kit.
Example - 2345-12-AR,
where 2345 is the contract number (contract) or cipher of the construction object;
12 - Room of the building or facilities by the General Plan *;
2345-12 - basic designation;
Ar is the brand of the main set of work drawings.
________________
* For partitions of the project related to the construction object as a whole (general explanatory note, the master plan and transport, etc.), as well as for the working drawings of linear structures, the master plan, outdoor communications, this part of the basic designation is usually excluded.
4.2.4 The main sets of work drawings include general data on working drawings, as well as drawings and schemes provided for by SPDS standards.
General data on working drawings
4.2.5 In the first sheets of each main set of work drawings, provide general data on working drawings, including:
a) the statement of the working drawings of the main kit in form 1;
b) the statement of reference and accompanying documents in form 2;
c) statement of the main sets of work drawings in form 2;
d) the statement of specifications (if there is mainly a set of several location schemes), performed in form 1.
e) the symbols not established by state standards and the meaning of which are not indicated on other sheets of the main set of work drawings;
e) general guidelines;
g) other data provided for by the relevant SPDS standards.
Forms 1 and 2 with instructions on their completion are given in Appendix B.
4.2.6 The statement of the working drawings of the main kit contains a consistent list of sheets of the main kit.
4.2.7 The statement of reference and attached documents is partitions:
a) reference documents;
b) the accompanying documents.
The "Reference Documents" section indicate the documents to which links in the working drawings are given, including:
a) drawings of typical designs, products and nodes with the name and indication of the series and the release numbers;
b) Standards that include drawings intended for the manufacture of products, indicating their name and notation.
Reference documents The project organization issues the Customer only on a separate contract.
The "Acceived Documents" section indicates the documents developed in addition to working drawings of the main kit, including:
Working documentation for construction products;
Sketch drawings of common types of non-type products *;
Specification of equipment, products and materials;
Local estimate;
Another documentation provided for by the relevant SPDS standards.
The accompanying documents of the project organization issues the Customer simultaneously with the main set of work drawings.
4.2.8 The statement of the main sets of work drawings leads on sheets of general data of the main set of the leading brand **.
If there are several main sets of working drawings of one brand, they constitute the statement of sets of this brand in form 2 of the application b, which is given on a sheet of common data for each of these sets.
* Perform if necessary.
** The main set of work drawings as the leading brand appoints the general designer.
4.2.9 In general directions, lead:
a) the basis for the development of working documentation (task for design, approved project);
b) the mark, adopted in the working drawings of the building or the construction conditionally for zero (as a rule, lead to architectural and construction drawings);
c) Recording on the results of verification of patentability and patent purity for the first time applied or developed in the project of technological processes, equipment, instruments, structures, materials and products, as well as numbers of copyright certificates and applications for which decisions have been made on issuing copyright certificates used in the working documentation of the invention;
d) record that work drawings are designed in accordance with applicable rules, rules and standards;
e) a list of types of work for which the acts of examination of hidden works should be compiled;
(e) Information about who owns this intellectual property (if necessary);
g) other necessary instructions.
In general guidelines, it should not be repeated technical requirements placed on other sheets of the main set of work drawings, and give a description of the technical solutions adopted in the working drawings.
5. General rules for execution of documentation
5.1 When performing project, working and other technical documentation, intended for the construction of enterprises, buildings and structures, the requirements of the relevant SPDS standards should be guided by the requirements of the unified system of design documentation (ECCD).
The list of ECC standards subject to accountable when performing graphic and text documentation for construction, is given in Appendix V.
The documentation intended for microfilming must comply with the requirements of the Reprography Standards System.
5.2 Drawings are performed at an optimal scale, taking into account their complexity and saturation of information.
The scale in the drawings do not indicate, with the exception of product drawings and other cases provided for in the relevant SPDS standards.
5.3 The list of cuts of words allowed in the main inscriptions, specifications, tables, drawings and specifications compiled in addition to GOST 2.316 and is given in Appendix G.
Coordination axes
5.4 In the image of each building or structure, the coordination axes indicate and assign them an independent system of designations.
Coordination axes are applied to the images of the building, facilities with thin barccotted lines with long strokes, denote by the Arabic numbers and the capital letters of the Russian alphabet (with the exception of letters: E, 3, th, o, x, c, h, s, ъ, s, b) In the circles with a diameter of 6-12 mm.
Skipping in digital and letter (except indicated) designations of coordination axes are not allowed.
5.5 figures indicate the coordination axes on the side of the building and facilities with a large number of axes. If there is not enough alphabet letters to designate the coordination axes, the subsequent axes are denoted by two letters.
Example - Aa; BB; Explosive
5.6 The sequence of digital and letter designations of the coordination axes take according to the plan from left to right and bottom up (Figure 1 but) or as shown in Figures 1 b., in.
5.7 The designation of the coordination axes is usually applied on the left and lower parties of the plan of the building and construction.
If the coordination axes of the opposite sides are discharged, the indication of the specified axes in the locations of discrepancies are additionally applied on top and / or right parties.
5.8 For individual elements located between the coordination axes of the main supporting structures, additional axes are applied and referred to them in the form of a fraction:
above the line indicate the designation of the preceding coordination axis;
under the line - an additional sequence number within the section between adjacent coordination axes in accordance with Figure 1 g.
Picture 1
It is allowed by the coordination axes of the half-timbered columns to assign digital and alphabetic designations to the continuation of the designations of the axes of the main columns without an additional number.
5.9 In the image of a repeating element attached to several coordination axes, coordination axes are denoted in accordance with Figure 2:
« but"- with the number of coordination axes of no more than 3;
« b.»-» »» »Over 3;
« in"- with all alphabetic and digital coordination axes.
If necessary, the orientation of the coordination axis, to which the element is attached relative to the neighboring axis, indicate in accordance with Figure 2 g..
Figure 2.
5.10 In order to designate the coordination axes of the residential building blocks, the index "C" is used.
Example - 1C, 2C, AC, BS.
On the plans of residential buildings arranged from block sections, the extreme coordination axes of block sections indicate without an index in accordance with Figure 3.
Figure 3.
Drawing, slopes, marks, inscriptions
5.11Realted line on its intersection with remote lines, loop lines or axial lines are limited by serifs in the form of thick main lines of 2-4 mm long, carried out with a slope to the right at an angle of 45 ° to the dimensional line, while the dimensional lines must appear for extreme remote lines. 1-3 mm.
When applying the size of the diameter or radius inside the circle, as well as the angular size of the dimension line is limited by arrows. Arrows are also used when applying the sizes of radii and internal rounds.
5.12 Level marks (heights, depths) of structural elements, equipment, pipelines, air ducts, etc. From the reference level (conditional "zero" mark) designate a conditional sign in accordance with Figure 4 and indicate meters with three decimal signs separated from an integer number. comma.
Figure 4.
The "zero" mark received, as a rule, for the surface of a building of a building or structure, located near the planning surface of the Earth, indicate without a mark; marks above zero - with a "+" sign; Below zero - with a sign "-".
On the types (facades), cuts and sections of the marks indicate remote lines or contour lines in accordance with Figure 5, on the plans - in a rectangle in accordance with Figure 6, except in cases specified in the relevant SPDS standards.
5.13 On the plans, the direction of the linker of the planes indicate the arrow over which, if necessary, is affixed by the magnitude of the slope in percent in accordance with Figure 7 or as a ratio of height and length (for example, 1: 7).
It is allowed, if necessary, the magnitude of the slope is indicated in the PROMILL, in the form of a decimal fraction with an accuracy of the third mark. In the drawings and schemes before the dimensional number that determines the magnitude of the slope, the sign "Ð" is applied, the sharp angle of which should be directed towards the slope.
The designation of the slope is applied directly above the line of the contour or on the shelf of the lifting line.
|
|
|
|
|
Figure 5. |
Figure 6. |
Figure 7. |
5.14 Remote inscriptions to multi-layer structures should be performed in accordance with Figure 8.
5.15 Rooms of positions (stamps of elements) are applied on shelves of lines-carrying, conducted from images of component parts of the subject, next to the image without a lifting line or within the contours of the samples of the object in accordance with Figure 9.
With a small-scale image, the lifting line finish without arrow and point.
5.16 The font size for referring to the coordination axes and positions (grades) must be on one or two rooms more than the font size adopted for the dimensional numbers on the same drawing.
Images (cuts, sections, species, fragments)
5.17 Cuts of buildings or structures are denoted by Arabic numbers sequentially within the main set of work drawings.
Independent numbering is allowed only for cuts of individual sections of the building, structures or installations, all the drawings of which are located on one sheet or sheet of sheets and if there are no references to cuts on these drawings located on other sheets of the main set of work drawings.
Sections are allowed to designate the capital letters of the Russian alphabet.
The direction of the view for a cut according to the plan of the building and the facilities is taken, as a rule from the bottom up and right to the left.
5.18 If separate parts of the form (facade), the plan, the cut require a more detailed image, then the remote elements are additionally performed - nodes and fragments.
5.19 When the node is image, the corresponding place is noted on the form (facade), plan, or a context with a closed solid thin line (usually a circle or oval) with a designation on the shelf of the lines of the sequence number of the Arabic node number in accordance with Figure 10.
If the node is placed on another sheet, then the number of the sheet is indicated under the shelf of the lifting line (Figure 10 but) or on the shelf of the lifting line next, in brackets, in accordance with Figure 10 b..
If necessary, reference to the node placed in another main set of work drawings, or on a typical node, indicate the designation and number of the sheet of the corresponding main set of work drawings in accordance with Figure 10 in Or a series of working drawings of typical nodes and a release number in accordance with Figure 10 g..
Figure 10.
On the image of the node indicate in the circle its serial number in accordance with Figure 12 but or 12. b..
|
|
|
|
Figure 11. |
Figure 12. |
An assembly, which is a complete mirror reflection of another (main) execution, is assigned the same sequence number as the main execution, with the addition of the "N" index.
5.20 Fragments of plans, cuts, facades, as a rule, are noted by a curly brace in accordance with Figure 13.
Figure 13.
Under the figure bracket, as well as the corresponding fragment, the name and sequence number of the fragment are applied. If the fragment is placed on another sheet, then give a link to this sheet.
5.21 images to the axis of symmetry of symmetric plans and facades of buildings and structures, arrangement of structural elements, plans for the location of technological, energy, sanitary and other equipment are not allowed.
5.22 If the image (for example, the plan) does not fit on the sheet of adopted format, then it is divided into several sections, placing them on separate sheets.
In this case, on each sheet, where the image section is shown, the scheme of a whole image with the necessary coordination axes and the symptoms (shading) of the image section shown on this sheet according to Figure 14 are shown on this sheet.
Note - If the drawings of the images of the image are placed in different basic sets of work drawings, then above the sheet number indicates the designation of the corresponding main kit (according to 4.2.2)
Figure 14.
5.23 If the plans of the floors of a multi-storey building have small differences from each other, then the plan is fully implemented by one of the floors, for other floors, only those parts of the plan are performed to show the difference from the plan shown in full.
Under the name of the partially depicted plan, record:
"The rest, see the Plan (name of the fully depicted plan)."
5.24 In the names of the flood plans of the building and structures indicate the netting of the net or floor number, or the designation of the corresponding secular plane.
Examples
1. Plan for OTM. 0,000
2. Plan 2 - 9 floors
3. Plan 3 - 3
When performing a part of the plan in the title indicate axes that limit this part of the plan.
Example - Plan for OTM. 0,000 between axes 1 - 8 and a - d
It is allowed in the title of the floor plan to indicate the purpose of the premises located on the floor.
5.25 In the names of the cuts of the building (structures), indicate the designation of the corresponding secular plane.
Example - Cut 1 - 1
5.26 In the names of the facades of the building and structures indicate the extreme axes, between which the facade is located.
Example - Facade 1 - 12
Main inscriptions
5.27 Each sheet of graphic and text document must have the main inscription and additional graphs for it. The forms of the main inscriptions and instructions on their completion are given in Appendix D.
5.28 In the design and working documentation, the main inscription is issued:
a) on sheets of basic sets of work drawings and basic drawings of project documentation - in form 3;
b) on the first sheet of drawings of construction products - in form 4;
c) on the first sheets of text documents and sketch drawings of common types of non-type products - in form 5;
d) on subsequent sheets of drawings of construction products, text documents and sketch drawings of common species - in form 6.
It is allowed on the first sheet of the construction product drawing the main inscription in shape 5.
5.29 In the reporting technical documentation on the results of engineering surveys, the main inscription is issued:
a) on sheets of graphic documents used in the design as a cauldron - in form 3;
b) on the first sheets of other graphic and text documents - in form 5, on subsequent sheets - in form 6.
5.30 The location of the main inscription and additional graph to it, as well as the dimensional framework on the sheets, are given in Appendix E.
5.31 Main inscriptions, additional graphs for them and frames are performed by solid thick basic and solid thin lines according to GOST 2.303 in accordance with the D. Annex
5.32 Graphic and text documents, brocked in the form of volumes, album, release or in another publishing form, are designated with a title list.
The rules for performing the title list are given in section 9.
5.33 The title page is allowed not to perform and not block text working documents of a small volume. In this case, the first sheet of the document is drawn up by the main inscription in form 3, subsequent - in form 6.
6 Rules for performing specifications in the drawings
6.1 To the location of the elements of the prefabricular design, monolithic reinforced concrete design, to the drawings of the installations (blocks) of technological, sanitary and other equipment are the specification in form 7 of the application J.
When performing drawings by the group method, group specifications in the form of 8 applications are
6.2 Construction Specifications are according to GOST 21.501.
7 Rules Amendments to working documentation issued to the Customer
7.1 Changing the working document previously issued to the Customer is any correction, exception or adding any data to it without changing the designation of this document. The designation of the document is allowed to change only when different documents are erroneously assigned the same designations or an error is made in the designation.
7.2 Changes contribute to the original document. Making changes to calculations is not allowed.
7.3 Copies of sheets (modified, additional and released instead of replaced sheets) of working documentation guide to organizations that were previously sent copies of documents, simultaneously with copies of the general data of the corresponding basic set of work drawings specified in accordance with paragraph 7.5.
7.4
7.4.1 Changing the document is performed on the basis of permission to make changes (hereinafter - permission) compiled in form 9 of Annex I.
The permission approves the head of the document developer organization or on his instructions another official.
7.4.2 The basis for obtaining original documents for making changes to the changes is permission.
7.4.3 Changes to each document (for example, the main set of work drawings, the specification of equipment and materials equipment) is made in a separate resolution.
It is allowed to make one general permission to change, introduced simultaneously in several documents if the changes are interconnected or the same for all changeable documents.
7.5 Alteration
7.5.1 Changes to the original documents are made by overclocking or clearing (washing). At the same time take into account the physical state of the original.
7.5.2 After making changes, letters, numbers, signs should be clear, thickness of lines, the magnitude of the lumen, etc., must be implemented according to the rules provided for by the relevant ECCD standards and Reprography standards system.
7.5.3 Changeable sizes, words, signs, inscriptions, etc. Excrying with solid thin lines and there are new data.
7.5.4 When the image is changed (part of the image), it is reduced by a solid thin line forming a closed loop, and crucifically crossed with solid thin lines.
A new image of the changed area is performed on a free field of a sheet or on another sheet without turns.
7.5.5 A variable, canceled and additional sections of the image assign the designation consisting of the sequence number of the next document change and through the point of the sequence number of the variable (canceled, additional) section of the image within this sheet. In this case, the new image of the changed area is assigned the designation of the changed image.
If a new image of the changed area is placed on another sheet, the changes assigned to it is preserved and in the table of changes of this sheet do not take into account.
7.5.6 Near each change, including about a change corrected by the clearing (washed), outside the image is applied to the parallelogram the designation of the change in accordance with Figure 15.
Figure 15.
From the parallelogram spend a solid thin line to the changed area.
7.5.7 Closely located varied dimensions, words, signs, inscriptions, etc. They will be reduced with a solid thin line, forming a closed circuit, without crushing in accordance with Figure 16.
7.5.8 If a new image of the modified area is placed on another sheet, then the replaced image also indicates the number of the sheet on which the new image is located in accordance with Figure 17.
|
|
|
|
Figure 16. |
Figure 17. |
7.5.9 Over the new image of the changed area is placed in the parallelogram, the designation of the change in the replaced image is placed, and at a parallelogram indicate: "In return crushed."
If a new image of the modified area is placed on another sheet, then at a parallelogram indicate: "In addition to the listed on the sheet (the sheet number on which the image is replaced)" in accordance with Figure 18.
Figure 18.
7.5.10 If a new image of the modified area is placed near the replaced, they are connected by liners with the notation of the change in accordance with Figure 19.
Figure 19.
Over the optional image is placed in the parallelogram the designation of the change, and at the parallelogram indicate: "Supplement" in accordance with Figure 20.
Figure 20.
7.5.11 When canceling an image (part of the image), the change indicates: "canceled".
7.5.12 If there is not enough space for making changes or a violation of the definition of the image when corrected is possible, then a new script is manufactured taking into account the changes made and retain its former designation.
If one or several sheets of the script is replaced or add or add, then they retain the inventory number assigned to the script.
When replacing all the script sheets, he is assigned a new inventory number.
7.5.13 When making changes to the sheets of the main set of work drawings in the statement of the working drawings of this kit on the sheets of common data in the "Note" column indicate:
a) when making the first change - "Change. 1".
When submitting subsequent changes - additionally, the next number numbers, separating them from the previous point with a comma.
Example - Change one; 2; 3.
b) on the replaced sheets under the change number - "(deputy.)."
Example - Change 1 (deputy)
c) on canceled sheets with the change number - "canceled".
Example - Change 1 (canceled)
d) on additional sheets with the change number - "(new)".
Example - Change 1 (new)
7.5.14 If the main set of work drawings include additional sheets, then they are assigned the next ordinal numbers and recorded in the continuation of the statement of the work drawings of the corresponding main kit.
With a lack of space in the statement of work drawings for recording additional sheets, the continuation of the statement is transferred to the first of the additional sheets. At the same time, at the end of the statement of work drawings placed in "General Data", record:
"For a continuation of the statement, see the sheet (sheet number)", and above the statement on the additional sheet, the title is placed: "The statement of the work drawings of the main kit (continued)."
The rooms and the names of the annulled sheets in the statement of the work drawings are burned.
When changing the names of sheets, appropriate changes in the Count "Name" are made.
7.5.15 With the change in the total number of sheets of the document on its first sheet in the main inscription, appropriate changes in the "Sheets" column are made.
7.5.16 When performing additional and cancellation of previously executed accompanying documents, corrections make corrections to the statement of reference and accompanying documents of the corresponding major set of work drawings.
7.5.17 When performing additional and cancellation of previously completed main sets of work drawings, corrections contribute to the statement of the main sets of work drawings.
7.5.18 Changes made to the script indicate a change table placed in the main inscription.
A table of change is allowed to put out the main inscription (above it or to the left of it) in the same form.
7.5.19 In the Change Table indicate:
a) in the column "Izm." - the sequence number of document change;
b) in the column "count. uch." - the number of variable sections of the image on this sheet within the next change;
c) in the column "Sheet" - on sheets released instead of replaced, "deputy.", on sheets added again, - "New".
When replacing all the sheets of the original (with the next number of document change) on the first sheet in the "Sheet" column indicate "All". At the same time, the table of changes on other sheets of this script is not filled.
In other cases, the column "Sheet" is puffed;
d) in the column "no doc." - permit designation;
e) in the column "sub." - the signature of the person responsible for the correctness of the changes (the signature of the person responsible for the normocontrol is put on the field to cover sheet);
e) in the "Date" column - the date of change.
7.5.20 The change table does not take into account the corrections made in the master data sheet in connection with the introduction of changes in the sheets of the main kit and the accompanying documents.
7.5.21 When you make changes to text documents, it is recommended to perform a table of registration of changes in form 10 of the position K. The registration table is placed on the title page of the text document.
7.5.22 Significant changes in text documents make one of the following ways:
a) replacing all or individual sheets of the document;
b) the release of new additional sheets.
When text documents are changed, it is allowed when adding a new sheet to assign the number of the previous sheet with the addition of another Arabic digit, separating it from the previous point.
Example - 3.1
In this case, on the first sheet, the total number of sheets change.
In text documents containing mainly solid text, it is allowed when adding a new item to assign it the number of the previous point with the addition of the next lower case letter of the Russian alphabet, and when the item is canceled - to save subsequent points numbers.
7.5.23 When canceling or replacing the document, all annulled and replaced sheets of the original are crosswise crossed with solid thin lines and stamped the stamp in form 11 of the application L.
8 Rules for binding working documentation
8.1. Working documentation - typical projects, typical design solutions (intended for binding) and working documentation of re-use are subject to reference to a specific construction site. On each sheet of the link documentation put a binding stamp in accordance with the application M:
a) on the first sheet - in form 12;
b) on subsequent sheets - in form 13.
8.2 covers and title sheets of the main sets of work drawings of typical projects (typical design solutions), published in the form of albums and issues, do not bind and cannot be sent to the customer.
8.3 The binding stamp is applied on a free field sheet, preferably above the main inscription or to the left of it.
8.4 It is allowed not to apply a binding stamp on immutable working drawings of structures, products and nodes if they are reused by the organization that has implemented the development and approval of these drawings. Specified work drawings are recorded in the section of the attached documents without changing the designation.
8.5 Changes in binding are made in accordance with PP. 7.5.1 - 7.5.4, 7.5.14-7.5.17 and subject to the following additional requirements:
a) if the variable sections of the image are two or more, then they are assigned sequence numbers that are affixed by Roman numbers on the shelf of the lifting line in accordance with Figure 21;
b) above the modified site indicate the Roman number of the sequence number of the variable portion of the image and the inscription "instead of crossed" in accordance with Figure 22.
If a new image (part of the image) is placed on another sheet, then the replaced image also indicates the number of the leaf on which the new image is located.
|
|
|
|
Figure 21. |
Figure 22. |
8.6 Basic inscriptions on sheets of the binding documentation published in the form of albums and issues are left unchanged.
8.8 Announced sheets exclude from the bound documentation without changing the total numbering of sheets.
9 Rules for issuing discharged documentation
9.1 Each discharged document is drawn up with a cover in form 14 given in Appendix N. The cover does not number and do not include in the total number of pages.
9.2 The first sheet of textual (graphic) document or several shutdown documents is the title page. The title page is performed in form 15 of the application P. Example of filling the title leaf is given there.
9.3 All sheets of a discrepanied document, starting with the title, must have through page numbering. At the same time, the title page does not name.
Page number on sheets of text and graphics documents is indicated in the upper right corner of the sheet of the sheet.
In addition, in the main inscription of text and graphics documents included in the album or release and having an independent designation, indicate the sequid numbering of sheets within the document with one designation.
9.4 When recruiting several documents in the form of volume, album or release after the title leaf, lead "content", which is performed in form 2 of the application B.
The first sheet of "content" is drawn up the main inscription in form 5 of Annex D, subsequent - in form 6 of the application D. "Content" assign the designation consisting of the designation of the document and the cipher "C".
Example - 2345-GT.S, 2345-11-kzh.Is, 2345-11-TX.NS
9.5 Title sheets of project documents are written in signatures:
supervisor or chief engineer organization;
chief engineer (architect) project.
Title sheets of working documents are issued by the signature of the responsible person - the chief engineer (architect) of the project.
The title list of reporting survey documentation is issued with the additional requirements of the relevant construction standards and rules.
9.6 The composition of the project, according to 4.1.2, lead in the statement performed in form 16 of the application R.
The statement leads a consistent list of project documentation volumes.
The first sheet of statement is drawn up by the main inscription in form 5 of the application D, subsequent - in form 6 of the application D.
Vedomosti assign the designation consisting of the basic designation of the document and through the hyphen - the cipher "SP".
Example - 2345-SP.
Brands of the main sets of work drawings
Table A.1.
|
Name of the main set of work drawings |
Note |
|
|
Production technology |
||
|
Technological communications |
When combining workers' drawings of all technological communications |
|
|
General Plan and Transport Construction |
When combining work drawings of the master plan and transportation structures |
|
|
General plan |
||
|
Architectural solutions |
||
|
Interiors |
Working drawings can be combined with the main set of the AR and AC brand |
|
|
Constructs are reinforced concrete |
||
|
Wooden designs |
||
|
Architectural and construction solutions |
When combining workers' drawings of architectural solutions and building structures |
|
|
Metal designs detail |
||
|
Water pipe and sewage |
||
|
Heating, ventilation and air conditioning |
||
|
Teplomechanical solutions of boiler rooms |
||
|
Air supply |
||
|
Dustovation |
||
|
Fooling |
||
|
Gas supply (internal devices) |
||
|
Power equipment |
||
|
Electric lighting (internal) |
||
|
Communication systems |
||
|
Radio communication, broadcasting and television |
||
|
Firefighting |
||
|
Fire alarm |
||
|
Security and Security and Fire Alarm |
||
|
Hydraulic solutions |
||
|
Automation ... |
Many replace the name and brand of the corresponding main set of work drawings |
|
|
Automation complex |
When combining workers' drawings of various technological processes and engineering systems |
|
|
Anticorrosive protection of structures, structures |
||
|
Anticorrosive protection of technological apparatus, gas ducts and pipelines |
||
|
Thermal insulation of equipment and pipelines |
||
|
Car roads |
||
|
Railways |
||
|
Construction of motor vehicles |
When combining workers' drawings of automotive, iron and other roads |
|
|
Exterior Water Supply Networks |
||
|
Outdoor sewage networks |
||
|
Outdoor network of water supply and sewage |
When combining workers' drawings of external water supply and sewage networks |
|
|
Heat mechanical solutions of thermal networks |
||
|
Outdoor gas pipelines |
||
|
Outdoor electric light |
||
|
Power supply |
||
|
Note ¾ If necessary, additional brands of the main sets of work drawings can be appointed. At the same time, capital letters (not three) of the Russian alphabet, corresponding to the brands, apply for stamps, appropriate, as a rule, the initial letters of the names of the main set of work drawings. |
||
Appendix B.
(mandatory)
Vedomosti shared data on working drawings
Form 1. - statement of working drawings of the main kit
Statement of specifications
Instructions for filling out the statement of working drawings of the main kit
In the statement of the working drawings, the main set indicate:
a) in the column "Sheet" - the sequence number of the sheet of the main set of work drawings;
b) in the "Name" column - the name of images placed on a sheet, in exact accordance with the names given in the main inscription of the sheet;
c) in the "Note" column - additional information, for example, changes made in the working drawings of the main kit.
Instructions for filling the statement of specifications
In the statement of specifications indicate:
a) in the column "sheet" - the number of the sheet of the main set of work drawings on which the specification is placed;
b) in the "Name" column - the name of the specification in exact accordance with its name indicated in the drawing;
c) in the "Note" column - additional information, including changes made in the specification.
Form 2. - statement of the main sets of work drawings
The statement of reference and accompanying documents
Instructions for filling out the statement of the main sets of work drawings
In the statement of the main sets of work drawings indicate:
a) in the graph "Designation" - the designation of the main set of work drawings and, if necessary, the name or distinctive index of the organization that has issued a document;
b) in the "Name" column - the name of the main set of work drawings;
c) in the column "Note" - additional information, including changes in the main sets of work drawings.
Instructions for filling the statement of reference and accompanying documents
The statement of reference and accompanying documents indicate:
a) in the graph "Designation" - the designation of the document and, if necessary, the name or distinctive index of the organization that issued the document;
b) in the "Name" column - the name of the document in full accordance with the name specified on the title page or in the main inscription;
c) in the "Note" column - additional information, including changes made to recorded documents included in the working documentation.
Appendix B.
Mandatory
List of ESCD standards subject to accountable when performing graphic and text documentation for construction
Table B.1.
|
Designation and name of the standard |
Conditions for applying Standard |
|
GOST 2.004-88 ESKD. General requirements for the implementation of design and technological documents on the printing and graphic devices of the Output |
|
|
GOST 2.101-68 ESKD. Types of products |
|
|
GOST 2.102-68 ESKD. Types and completeness of design documents |
Taking into account the requirements of GOST 21.501, belonging to the performance of the drawings of construction products |
|
GOST 2.105-95 ESKD. General requirements for text documents |
Taking into account the requirements of Section.4, 5 and 9 of this standard |
|
GOST 2.108-68 ESKD. Specification |
Taking into account the requirements of Section 6 of this Standard and GOST 21.501 |
|
GOST 2.109-73 ESKD. Basic requirements for drawings |
|
|
GOST 2.113-75 ESKD. Group and Basic Design Documents |
Taking into account the requirements of GOST 21.501 |
|
GOST 2.114-95 ESKD. Technical conditions |
Taking into account the requirements 5.27, 5.28, 5.30-5.32 of section 5 and Section 9 of this Standard. 3.7.1 and 3.8 GOST 2.114 do not take into account |
|
GOST 2.301-68 ESKD. Formats |
Taking into account the requirements of the relevant SPDS standards |
|
GOST 2.302-68 ESKD. Scale |
|
|
GOST 2.303-68 ESKD. Lines |
|
|
GOST 2.304-81 ESKD. Drawing fonts |
|
|
GOST 2.305-68. ESKD. Images - species, cuts, sections |
Taking into account the requirements 5.17-5.26 of this standard |
|
GOST 2.306-68. ESKD. Designations Graphic materials and rules for their application in drawings |
Taking into account the requirements of GOST 21.302, Tables 4 and 5 |
|
GOST 2.307-68 ESKD. Differences and limit deviations |
Taking into account the requirements 5.11-5.13 of this standard |
|
GOST 2.308-79 ESKD. Note on drawings tolerances forms and location of surfaces |
Taking into account the requirements of GOST 21.113 |
|
GOST 2.309-73 ESKD. Roughness designation surfaces |
|
|
GOST 2.310-68 ESKD. Application in drawings of designations of coatings, thermal and other types of processing |
|
|
GOST 2.311-68 ESKD. Image of thread |
|
|
GOST 2.312-72 ESKD. Conditional images and designations of welded joints |
|
|
GOST 2.313-82 ESKD. Conditional images and notation of all-point connections |
|
|
GOST 2.314-68. ESKD. Indications in drawings on marking and branding products |
|
|
GOST 2.315-68 ESKD. Images simplified and conditioner fasteners |
|
|
GOST 2.316-68 ESKD. Rules for applying in drawings of inscriptions, technical requirements and tables |
Taking into account the requirements 5.14-5.16 of this standard |
|
GOST 2.317-69 ESKD. Axonometric projections |
|
|
GOST 2.410-68 ESKD. Rules for performing drawings of metal structures |
|
|
GOST 2.501-88 ECCD. Storage Accounting Rules |
In the form of the inventory book, subscriber card and instructions for folding drawings |
|
Note - The conditions for the application of ECC standards of the classification group 7 are defined by the relevant SPDS standards. |
|
List of permissible cuts of words (Supplement to GOST 2.316)
Table G.1.
|
Full name |
Abbreviation |
|
Highway |
|
|
Antisaismic seam |
|
|
Architect |
|
|
Asphalt concrete |
|
|
Concrete, concrete |
|
|
Ventilation camera |
ventscamera |
|
Chief Engineer |
GL Ing. (*) |
|
Chief Engineer (Architect) of the Project |
GUI (HAP) (*) |
|
Chief Specialist |
GL specialist. (*) |
|
Expansion joint |
|
|
Director |
|
|
Document |
|
|
Permissible |
|
|
unit of measurement |
Units. change (t) |
|
EMK. (C, T) |
|
|
Railway |
|
|
Reinforced concrete, reinforced concrete |
|
|
Head |
|
|
Insulation, isolation |
|
|
Institute |
|
|
Design |
|
|
Coefficient |
|
|
Efficiency |
|
|
Staircase, stairs |
|
|
Workshop (in project organizations) |
|
|
Materials |
mat-lies |
|
Mounting |
norm. Narr. |
|
Equipment |
|
|
Checked |
|
|
calculate Narr. |
|
|
Sanitary-technical |
san. tehn |
|
Toilet |
san. knot |
|
Well |
|
|
Snow |
|
|
Temperature seam |
|
|
Technological |
|
|
Rail head level |
ur. G. R. (and) |
|
Ground level |
|
|
Pure floor level |
ur. h. p. (and) |
|
Foundation |
|
|
Cement, cement |
|
|
Cement concrete |
|
|
Plaster |
|
|
Crushed stone, rubble |
|
|
Electric |
|
|
eL-T (and. T) |
|
|
Note - Abbreviations marked with a sign (*) apply only in the main inscription; (T) - in the tables; (C) - with numbers or ciphers; (and) - in graphic images |
|
Appendix D.
(mandatory)
Basic inscriptions and additional graphs for it
Form 3 - For sheets:
major sets of work drawings;
major drawings of project documentation sections;
graphic Documents on Engineering Exquisites
Form 4 - DLi draw construction products (first sheet)
Form 5 - For All types of text documents (first sheets)
Note - The main inscription in form 5 is allowed to use for graphic documents on engineering surveys that are not used as a shipment
Form 6 - For drawings of building products and all types of text documents (subsequent sheets)
Note - The main inscription in form 6 is allowed to be used for graphic documents on engineering surveys not used as a share
Instructions for filling the main lettering and additional graph to it
In the graphs of the main inscription and additional graphs to it (the number of the graph is listed in brackets) lead:
a) in column 1 - the designation of the document, including the project section, the main kit of working drawings, product drawing, textual document, etc.;
b) in column 2 - the name of the enterprise, the housing and civil complex or another construction object, which includes a building (structure), or the name of the neighborhood;
c) in the column 3- the name of the building (structures) and, if necessary, the type of construction (reconstruction, expansion, technical re-equipment, overhaul);
d) in column 4 - the name of images placed on this sheet, in exact accordance with the name in the drawing.
Names of specifications and other tables, as well as text indications related to images, do not indicate in the column;
e) in column 5 - the name of the product and / or the name of the document;
e) in column 6 - the conditional designation of the design stage:
1) P - for project documentation, including the approved part of the working draft;
2) P - for working documentation;
g) in column 7 - the sequence number of the sheet or the page of a text document during duplex printing. On documents consisting of one sheet, the graph is not filled;
and) in column 8 - the total number of sheets of the document. The graph is filled only on the first sheet.
On the first sheet of a text document, during duplex printing, the total number of pages indicate;
k) in column 9 - the name or distinctive index of the organization that has developed a document;
l) in column 10 - the nature of the work performed (developed, checked, normocontrol).
Depending on the design stage, the complexity and significance of the document, free lines are allowed to fill out at the discretion of the organization's management (specify the posts of persons responsible for developing a document (drawing);
m) in graphs 11-13 - surnames and signatures of the persons listed in column 10 and the date of signing.
Signatures of other officials and matching signatures are placed on the field to cover sheet;
h) in columns 14-19 - Count Count Counts, which are filled in accordance with clause 7.5.19;
n) in column 20 - the original number of the original;
p) in column 21 - the signature of the person who accepted the script for storage, and the acceptance date (number, month, year);
c) in column 22 - the inventory number of the original document, in return to which the original was issued;
t) in column 23 - the designation of the material of the part (the graph is filled only in the drawings of the parts);
y) in column 24 - a mass of the product shown in the drawing, in kilograms without specifying a unit of measurement. The mass of the product in other units of measurement is given with an indication of the unit of measurement.
Example - 2,4 t;
f) in column 25 - scale (they are affixed in accordance with GOST 2.302);
w) In column 26 - the signature of the person who copied the drawing (if necessary).
Appendix E.
(mandatory)
Location of the main inscription, additional graph to it
and dimensional frames on sheets
Note - Dimensions in brackets are listed for the framework of typical project documentation.
Appendix J.
(Mandatory)
Shape 7 - FROMpsychification
Form 8 - G.ruPP Specification
Instructions for completing the specification and group specification
In specifications indicate:
a) in the column "pos." - positions (brands) of structural elements, installations;
b) in the graph "Designation" - the designation of the main documents to the elements of structures, equipment and products or standards (technical conditions) on them recorded in the specification (technical conditions) on them;
c) in the column "name" - the name of the elements of structures, equipment and products and their brand. It is allowed to group the same elements indicate the name once and emphasized;
d) in the column "count." Form 7 - the number of items. In the column "Count ..." forms 8 Instead of dots, write "according to the scheme", "on the floor", etc., and below - the ordinal numbers of the location or floors;
e) in the column "Mass, units" - a mass in kilograms. It is allowed to give a mass in tons, but indicating a unit of measurement;
e) in the "Note" graph, for example, for example, a mass measurement unit.
Appendix I.
(mandatory)
Form 9 - Permission to make changes
Instructions to fill the permission to make changes
In the resolution graphs indicate:
a) In column 1 - the designation of the permission consisting of the order number of permission on the registration book of permissions according to GOST 21.203 and through the Last Digital Defisc.
Example - 15-97;
b) in column 2 - the designation of the document in which the change makes;
c) in column 3 - the name of the enterprise under construction, buildings (structures);
d) in column 4 - another serial number assigned to changes that contribute to a document in one permission. It is indicated for the whole document, regardless of how many sheets it is completed. The ordinal numbers of the changes are denoted by Arabic figures;
e) in column 5 - numbers of sheets of a document that make changes;
e) in column 6 - the content of the change in the form of a text description and / or graphic image;
g) in column 7 - the cause code of change in accordance with the table
and) in column 8 - additional information;
k) in graphs of 9-11 - the names of persons signing permission, their signatures and the date of signing;
l) in column 12 - the name of the project organization and division (department), which resolved;
m) in columns 13-16 - the name of the relevant units or organizations, positions and the names of persons with whom in the prescribed manner agree on permission, their signatures and the date of signing, as well as the signature of the normocontroller;
h) In column 17 - the sequence number of the resolution sheet. If the resolution consists of one sheet, the graph is not filled;
p) In column 18 - the total number of resolution sheets.
Form 10 - Table registration table
Guidelines for completing the Change Registration Table
In the graphs of the Change registration table indicate:
a) in graphs "change", "number dock", "sub." and "date" - similar to the fill in the corresponding graph of the change table;
b) In the graphs "of sheet numbers (pages) of modified, replaced, new, canceled" - numbers of sheets (pages), respectively, modified, replaced, added and canceled for this permission.
When replacing the entire document in the column "sheet numbers (pages), replaced" indicate "all";
c) in the column "all sheets (pages) to the dock." - The number of sheets (pages) in the document. The graph is filled in case of filling the graph "of sheet numbers (pages), new" and / or "numbers of sheets (pages), canceled".
Appendix L.
(mandatory)
Shape 11 - Cancellation stamp (replacement) of the script document
Instructions for filling the cancer (replacement) of the script sheet of the document
In the stamp indicate:
a) In line 1 - the sequence number of the next document change, according to which the sheet is canceled or replaced (for example, "out. 3"). When canceling a sheet, the word "replaced" in the stampe is burned;
b) in graphs 2-5 - the position, surname, signature of the person responsible for making changes and the date of signing.
Appendix M.
(mandatory)
Shape 12 - Binding stamp (first sheet)
Shape 13 - Binding stamp (subsequent sheets)
Instructions for filling binding stamps
When filling the binding stamps indicate:
a) in column 1 - a new designation of a given document;
b) in column 2 - the name of the organization that has been binding;
c) in column 3 - the name of the enterprise under construction, buildings or structures for which a binding is made;
d) in graphs 4-7 - posts and surnames of persons responsible for binding, as well as persons that made the normocontrol, their signatures and dates of signing;
e) in column 8 - an inventory number assigned to a tied document;
e) in column 9 - the number of sheets of a tied document;
g) in columns 10, 11 - signature of the person who has tied a storage document and the date of signing.
Appendix N.
(mandatory)
Form 14 - Cover
Note - The name of the management authority indicates state organizations.
Appendix P.
(mandatory)
Form 15 - Title page
Notes
1 The name of the management body indicates state organizations.
2 The field for signing the document is filled in accordance with the instructions in Section 9.
An example of a title page
Appendix R.
(mandatory)
Form 16 - The composition of the project
Instructions for filling the statement
In the statement indicate:
In the column "Tom number" - the number of the volume or its part;
In the graph "Designation" - the designation of the document indicated on the title page, and, if necessary, the name or distinctive index of the organization that issued a document;
In the column "Name" - the name of the document in exact accordance with the name specified on the title page;
In the column "Note" - additional information.
Keywords: working documentation, working drawings, general data on working drawings, composition, main kits, specifications, changes, binding, project documentation, graphic and text documents, title sheet, basic inscriptions, signatures.
1 area of \u200b\u200buse
3 General documentation requirements
4 General Requirements for the Acquitations of Documentation
4.1 Project documentation
4.2 Workers drawings
General data on working drawings
5 General Rules for the implementation of documentation
Coordination axes
Drawing, slopes, marks, inscriptions
Images (cuts, sections, types , Fragments)
Main inscriptions
6 Rules for performing specifications in the drawings
7 Rules for making changes to working documentation issued to the Customer
7.4 Permission to make changes
7.5 Amendments
8 Rules for binding working documentation
9 Rules for issuing discharged documentation
Application A brand of main sets of work drawings
Appendix B forms 1 and 2- Validity of general data on working drawings
Appendix in the list of ESCD standards subject to accountable when performing graphic and text documentation for construction
Appendix G The list of permissible cuts of words (Supplement to GOST 2.316)
Appendix D shape 3-6 - Main inscriptions and additional graphs for it
Appendix E Location of the main inscription, additional graph to it and dimensional frames on sheets
Appendix F forms 7 and 8- Specifications
Annex and form 9 - permission to make changes
Appendix to Form 10 - Change Change Table
Appendix L shape 11 - cancellation stamp (replacement) of the script of the document
Appendix M forms 12 and 13- binding stamps (first and subsequent sheets)
Appendix N Form 14 - Cover
Appendix P form 15 - Title leaf. An example of a title page
Appendix R Form 16 - Project Composition